Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Washer Vibration Sensor Assembly by Samsung

Best Seller
Manufacturer Part
4.89 (64)
By: Samsung
Part Number: OEM16737933
Manufacturer Part Number: DC93-00278B

The Washer Vibration Sensor Assembly is essential for maintaining the stability and performance of your Samsung washer. This genuine OEM part accurately detects and manages the vibration levels during wash cycles, ensuring your machine operates smoothly and efficiently. By replacing a faulty sensor with this high-quality assembly, you can prevent excessive shaking and potential damage to your appliance. The Washer Vibration Sensor Assembly is designed to fit a wide range of Samsung washer models, guaranteeing a perfect match and straightforward installation. With its reliable performance, this sensor helps extend the lifespan of your washer, providing peace of mind and optimal functionality. Investing in this genuine OEM part ensures that your Samsung washer continues to deliver excellent washing results while minimizing noise and movement. Whether youGÇÖre troubleshooting an existing issue or aiming to enhance your washerGÇÖs performance, the Washer Vibration Sensor Assembly offers a dependable solution for a better laundry experience.

More
$93.49

IN STOCK
Ships Today Guaranteed
Add to Cart

Questions & Answers

For Samsung Washer Vibration Sensor Assembly (Part Number: OEM16737933)

1 Answer

Kein, you will want to test the suspension rods DC97-05280S to ensure that they are in good condition. If you press the tub down as far as it will go, while empty, and then quickly release the tub, it should rise right up and set back into it's normal position. If the tub bounces up and down before it settles into place, then your suspension rods are bad. If the output from the MEMS sensor is over 4.5V or under 0.5V and it continues for 5 seconds, this error occurs. You will need to check the wire connector terminals between the MEMS sensor and PBA connector CN8. If no problem found, either the MEMS Sensor DC93-00278B or the main control DC92-01021V will need to be replaced.

Read More...

1 Answer

Travis, the MEMS sensor is going to be located on the bottom of the tub assembly near the clutch shifter.

Read More...
Jared for Model Number Wa50k8600av/aa

Samsung washer gives me an 8c error code. Replaced mems sensor. Still has the same issue. However if you lean the washer backwards about halfway it will run without throwing the 8c code. Soon as you set it back on all 4 feet the code comes right back. I've checked all the harnesses doesn't seem to be a break in the wiring. I'm thinking the board isn't reading the sensor properly. Do you have many faulty wiring harnesses or more faulty control boards? Any help would be greatly appreciated.. thank you for your time

1 Answer

Jared,

Visually inspect the wiring harness between the main control board and the mems sensor and if the wiring checks ok then this should be an issue with the main control board.

Read More...
Greg W for Model Number Samsung WF218ANW/XAA

When the washer gets to the spin/drain cycle, sometimes it will work, but more often than not lately it doesn't drain or spin. If you leave to sit long enough, usually it will give the no drain error. Bought a new pump, installed and it worked the first cycle, then went back to mostly not draining/spinning. Took back apart, took off all hoses and cleaned them, making sure there was no blockage. Same result. What else could be causing this issue? The main control board? Could a sensor possibly cause it to not drain/spin? Thanks.

1 Answer

Greg,

Check the pressure hose to make sure that the hose is not clogged and if it is not clogged then either the pressure switch is faulty or the main control board is faulty.

Read More...

1 Answer

Michael, the mems sensor [DC93-00278B] is located in the control panel at the front of the user interface control. You would need to remove the selector knob and the rear control cover panel before being able to remove the front panel. Once the rear panel is removed, the front panel would then be removed and the control will be held in by screws. Once you remove the user interface board, the mems sensor will be accessible.

Read More...

1 Answer

Sarven,
Having issues pulling a parts breakdown and technical data from the model you listed but the 8E error is a mems sensor error.

Read More...

1 Answer

Jacob,
You shouldn't have any issues just go slow and take pictures of wire locations so there's no problem on reassembly. The main control is attached behind the console by clips, simply separate and change the board.

Read More...

1 Answer

Jacob,
That is still an error code for the mems sensor. Check all wire harness connections and if no loose connections then you would replace the board. DC92-01021V

Read More...

1 Answer

Andre, The [AP5579308} Assy. Sensor; Mems Sensor is located on the bottom of the wash basket, in the area of the clutch assembly. It's held in position by two(2) screws and has a locking wire harness connection. You may find it easier to disconnect the fill and drain hoses and lay the washer on it's back or side to access the sensor. Another option is to walk the washer away from the wall and lean it back and rest it against the wall, block it up and crawl or lay underneath the washer.

Read More...

1 Answer

NAS, The MEMS/ Off BAlanced load sensor should produce an off balance load display, so should other components for the matter. You didn't mention any noises but you may want to check to see if the tub bearings are worn and causing the tub to "wobble" during the ramp up of the drum speed. Rotate the spin tub to 3 or 4 different positions and push up on the front edge/lip of the spin basket, there should be very little up and down movement of the tub. make sure the washer is level and as close to the floor as possible, then check the suspension dampers for proper and "free" movement. Then check the motor hall sensor and wiring, this could also cause the symptoms you described, but should also display
an error code.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google