Stan Flewelling March 03, 2017 for Model Number RFG297AARS/XAA Ice maker makes a clicking sound that sounds like a gear is stripped and does nothing. No water in tray, nothing. Then stops after a while.
1 Answer Stan, The DA97-00258E ice maker head, will not work in the model number you supplied. The correct part number is DA97-05422A / DA97-05422A Ice Maker Assembly. It is a "sealed" or "complete" assembly and will need to be replaced as a "unit". Unfortunately, the part is out of stock at this time. It would require a few extra days(5 to 10) to order the part from the manufacturer and deliver it to you, once the order is placed. Thanks, Read More...
Mark February 15, 2017 for Model Number RS2630SH I was looking for ice maker parts, and found this Icemaker head AP4167887. However, since I am not completely confident that this is the problem, I also followed the following link: For the complete ice maker assembly order DA97-02203H. I have 2 questions: 1) How come the complete ice maker assembly does not appear to be compatible with my refrigerator (RS2630SH), yet the wording prior to the link appears to indicate that it does? 2) If that is not the correct link for the complete ice maker assembly, does the correct part exist on your website? Thank you, -Mark
1 Answer Hello Mark. The model number you provided uses the D series icemaker and not the E series. You will need to order DA97-00258D for the correct icemaker. Read More...
1 Answer Hello James, This is most likely the water valve DA62-00914B not closing properly. This can be caused by the water valve failing, low water pressure to the unit from the home plumbing, or a sticking contact in the icemaker assembly DA97-02203G. Read More...
Patsy September 23, 2016 for Model Number RF34H9960S4/AA-0000 Icemaker making wet ice cubes and dripping water also when you dispense ice some water is in with ice what is going on?
1 Answer Hello Patsy. Check and make sure the temp is 0 to 5°. If so, you will need to replace the icemaker. If not, you will need to adjust the temp. Read More...
James August 10, 2016 for Model Number RB195BSSB/XAA The turn off arm on my ice maker,da6101805, has broken. Can I get just the replacement arm.
1 Answer Hello James. No, you will need to order the icemaker head DA97-00258E for the arm that is needed. Read More...
James August 06, 2016 for Model Number RB195BSSB The plastic turn off lever has broken off of the ice maker # DA61-01805. Can I get this part without buying the complete head.
1 Answer James, You would need to get the icemaker head in order to get the lever as it is not available as a separate part. The part number for the icemaker head is DA97-00258E. Read More...
Allan March 27, 2016 for Model Number RFZ66ABPN On the ice maker control modul,the white rectangular plastic end of the sensor is dangling tho' the wires are intact andthe other end is connected. Where does the white rectangular end of it connect or go so it's not hanging down?
1 Answer Hello Allan. It attached to the bottom of the ice tray. if it is broken you will need to order and replace the ice maker assembly on the unit. Read More...
Donna H March 18, 2016 for Model Number rb195sbss Bought the ice maker head from you, is there a video that shows how to install... Not a single piece of paper with my order.... so there must be something online! thanks, D
1 Answer Donna, Here is a link to a similar model that is a video for replacing the icemaker. https://www.youtube.com/watch?v=u_NnNsn6y1E Read More...
Ryan February 19, 2016 for Model Number RS2530BBP The sensor on my ice maker's control module somehow was ripped off. Is there a replacement that can be bought, or a way to bypass this sensor?
1 Answer Ryan, Unfortunately the sensor cannot be replaced separately and you will need to get the icemaker head in order to replace it. Read More...
Debbie February 16, 2016 for Model Number RB215BSSB Can you order the gear only instead of the whole front motor box? The motor works. One of the teeth are broken on the large gear.
1 Answer Debbie, Unfortunately the gear cannot be ordered as a separate part and you will need to get the front motor box. Read More...