Eric February 02, 2018 For the overload protection relay, there is power on the brown wire side but not on the blue wire side of the part. Does this mean the part is bad? Should there be power on both sides if it's good?
1 Answer Hello Eric, I'm sorry but we will need to ask you to post a new question including the model number from your units' I.D. tag so we can pull the wiring diagram for the unit you are servicing. This will enable us to see what you are seeing and provide you with accurate, pertinent information. Thank you for your patience and understanding in this matter. Read More...
Brad January 31, 2018 for Model Number RSG257AARS/XAA-0000 I submitted a question about the compressor protector/relay. I was trying to test it and removed the brown and blue wires that connect to the pins, but forgot to make a note of which one was connected to which pin. I got an answer back, which I appreciate. I just need more clarification. The answer states, "The blue goes to the pin on the back and the brown to the pin on the side of the overload." I am just trying to make sure I don't mess this up, so how would I be looking at the compressor protector to know which pin is considered the back pin and which one is the side one? Depending on how I look at the protector, the pins would change position. Do I hold it as if it is mounted on the compressor? Also, if I shake it, should it rattle or is that a good sign it needs to be replaced?
1 Answer Hello Brad. Yes, you look at it as if it were mounted to the compressor. The overload will rattle a little if you shake it. That is normal. Read More...
Brad January 30, 2018 for Model Number RSG257AARS/XAA-0000 Trying to replace compressor protector, part number DA34-00004D. I can remember which pin the blue wire and brown wires connected to. I don't want to reverse them. I've looked at the wiring diagram and don't know how to read it well enough to figure it out.
1 Answer Hello Brad. The blue goes to the pin on the back and the brown to the pin on the side of the overload. Thank you. Read More...
Shawn September 28, 2017 for Model Number RF18HFENBWW/AA Hello,I'm trying to replace the relay on my refrigerator. I'm assuming the relay is located under the black plastic cover attached to the compressor. If so, how do I remove that cover so I can get to the relay? Thanks.
1 Answer Hello Shawn. Insert a flat blade into the slot on the cover and pry downward to release and remove the cover from the unit. Thanks. Read More...
Kat T September 15, 2017 for Model Number RFG298AABP/XAA How do I remove the wire harness(black part) from the white OL relay?
1 Answer Kat, The wire connector will just pull off the overload relay on the unit. If you need to get under the connector with a pair of needle nose pliers and push off the connector. Read More...
Mr. Kishon August 06, 2017 for Model Number RF4287HARS/XAA The compressor is not coming on; the fan is working. Removing the panel I see that there is oil in the pan under the compressor. I am getting a 4 blinking light code: Motor Locked / Over RPM. 1) Is the compressor bad? 2) Is there a way to bump start the compressor? 3) The blinking light chart suggest to "Short the shunt resistor between leads". How do I do that? I did get continuity between the comp terminals, but one terminal is giving me around 120 Ohm. I am getting no Amp to the common terminal on the comp. Any other suggestions would be helpful.
1 Answer Mr. Kishon, When it says that the shorted shunt resistor between the leads could be a bad inverter but in most cases this will be a locked rotor on the compressor or a short in the compressor of the unit. Read More...
Charlie May 25, 2017 for Model Number RFG298AARS/XAA My refrigerator has stopped cooling, the compressor is not working. The inverter board is flashing the red light 5 times, according to Samsung manual it means low voltage. I checked the voltage at pin 4 on cn79 (as repair manual states). It asks if voltage is high? (2.5volts). It had 0 volts and then says to replace PCB. Do these boards fail often? Is there a way to test the inverter board and/or compressor? Thanks.
1 Answer Charlie, According to the PCB breakdown you would want to test the CN75 connector from pin 4 to pin 3 which should be orange to red. If there is not 2.5vdc then the main PCB board would be faulty and need replaced. Read More...
Hisham April 26, 2017 for Model Number RFG297AARS/AA Samsung french door My fridge temperature 50 and the freezer is 65 The compressor is working the cooling fan for it also working the interior cooling fans are working I changed all the freezer thermostats. when I plug the cord the freezer evaporator inlet pipe start getting could for seconds then it stops and starts getting warmer. Any Ideas. thank you
1 Answer Hello Hisham. Based on the information you provide, it sounds like the sealed system has failed and you will need an HVAC tech to come out and repair the unit. Read More...
Eric January 24, 2017 for Model Number samsung rfg298hdwp/xaa. I have ice buildup under deli drawer and freezer drawer on a 5 year old samsung rfg298hdwp/xaa. Is it just iced over drain lines or is there a bad sensor involved?
1 Answer Hello Eric. You will need to clean out the drain line. Then install a redesigned drain clip DA61-14306A. Read More...
Henry August 18, 2016 for Model Number RF32FMQDBSR/AA-0000 My Samsung freezer working but refrigerator is not cool. It keep the temperature around 57. I check the Evaporator Assembly and found a little oil, a very tiny hole on the aluminium coil where the oil come. I think the freon is leaking. It use R600a freon. Is it repairable? Can add R600a freon to my refrigerator? Please help me. Thanks.
1 Answer Hello Henry. You have sealed system failure and will need an HVAC tech to come out and repair the unit. You have to be certified to repair these. Read More...