Tim May 29, 2024 for Model Number samsung WF45N5300AF/US The machine won't unlock after a cycle. I replaced the door switch assembly and it still isn't unlocking. It seems to wash fine, it just won't unlock the door when it's done. I tried draining the tub and that had no effect. At this point, should I replace the sensor board? Thanks for the help!
1 Answer Hello Tim, thank you for contacting APP,It is possible that the unit is not seeing the tub as having stopped or being properly empty of water, thus preventing the door from unlocking. The 1st thing I would recommend to try is running the Self-Clean+ cycle located on the right-hand side of the display, this will flush the pressure and drain systems to remove any detergent residue and/or other debris that has built-up in the system, I would also recommend to add about 2 cups of White Vinegar to the unit before you run the Self-Clean+ cycle to aid in removing any detergent residue. If the issue continues after running this cycle I would recommend to have the Diagnostic Mode run, and the system checked for any error codes that may have been generated due to the issue. Read More...
Steven February 08, 2024 for Model Number wf45k6500av/a2 I have a Samsung washer model: wf45k6500av/a2. I am getting error DC3 which points to the door lock switch being the issue. I replaced it with part DC64-00519D and it worked for about 5 wash cycles. Now I am getting error DC3 again. My question is, is there something that might cause the switch assembly to go bad? Like the computer panel causing a short? Any other parts I should also test/replace along with the switch assembly? Thanks in advance.
1 Answer Steven, The DC3 error code can be any of the following: 1. The Door lock switch terminal is connected incorrectly. 2. The Door lock switch terminal is broken.3. This occurs intermittently because of an electric wire leakage. (shorted or broken)4. A main PCB fault.Using a multimeter check the switch and the wiring. If both check good then you could have a PCB failure. Read More...
Eyad December 01, 2023 for Model Number 970-C480590 serial 4C11605615 does the door latch DC64-00519B fit my washer. the original part is DC64-00519D. thanks
1 Answer Eyad, as the original part number is DC64-00519D it is recommended that the latch is used. The use of an alternative such as the switch assembly DC64-00519B can not be guaranteed to work properly. Read More...
Brooke February 28, 2023 for Model Number Samsung FlexWash WV55M9600AV/A5 02 I'm looking for the door lock assembly that will work for the Samsung FlexWash WV55M9600AV/A5 02. Would you be able to confirm which assembly is the right one? Thank you!
1 Answer Brooke, the door switch assembly DC64-00519D would be used with the model number provided. Read More...
Steve W December 30, 2022 for Model Number wv60m9900av/a5 The lower main washer starts up, tests fill valve, then drains water out, then shuts of completely.
1 Answer Steve, It would be recommended to get the tech sheet from inside the unit and see if there are any error codes stored. This will guide you to what may be going on with the unit. Read More...
Travis May 08, 2022 for Model Number WF45K6200AW/A2 Does this switch assembly include the switch for the add-wash add door?
Dpw March 17, 2022 for Model Number Samung WF45R6100 AC/US 00 Is Samsung AP6027082 / DC64-00519D Door Switch Assembly the correct door switch assembly for my model?
Giridhar October 04, 2021 for Model Number WF42H5000AW/A2 Hi. For my model does dc64-00519B work? Or do I have to get dc64-00519D?
1 Answer Giridhar, the door switch assembly DC64-00519B would be used with the model number provided. Read More...
Andrew March 02, 2019 for Model Number WF218ANS/XAC 01 Will this door lock work on my Samsung washer?
1 Answer Hello Andrew, the manufacturer list part number DC64-00519B as the correct unit for your model number. Thanks! Read More...
Mike Michalopoulos September 16, 2017 for Model Number WF331ANW/XAA-0004 On the phone with your tech people. I installed the door latch assembly DC64-00519D for this washer. All it did when I started the wash cycle is a short buzz, then another, then another, then it stopped its cycle and showed a code of FL. I cannot get the door open. My kids P.E. clothes are in there. I need to get them out! APP is sending me another part which does me no good unless I can get the door open.
1 Answer Mike, If you take the top of the washer off you can reach to the bottom of the latch assembly and there will be a tab you pull down on to get the latch unlocked. Read More...