Gregery December 04, 2023 for Model Number DU1100XTPSB Hi All the lights are flashing on the touch pad. unplugging does not help
1 Answer Gregery, Usually the lights all flashing is because the unit thinks the door is opened on most units. You might also have a shorted keypad. Remove the console and take off the control that the membrane switch is attached to. If you find the green clear membrane to have any dark spots then it would need to be replaced. Read More...
Jeff April 08, 2022 for Model Number 66513742K601 Control panel seems to only allow selection of "Pots and pans". When "cancel/drain" is selected, pump runs, but never stops. Door handle has no spring action. Actuator seems like it should have a spring?
1 Answer Hello Jeff, You should run the diagnostics to pull any fault codes. If there are fault codes, you should look them up on the tech sheet behind the kick panel and run any tests advised on the sheet. If not, you may need to replace the control board WPW10084141. Read More...
Gary October 14, 2020 for Model Number KUDK01ILBS3 I replaced the door latch handle and door latch bracket, but did not replace the actuator. The door now works as it should and properly latches and lights come on but the unit still will not run. Should I replace the actuator?
1 Answer Gary, You will want to test the door switch for continuity when the red tab is depressed and the actuator should actuate the switch. If you remove the outer panel you can see how the latch operates. Read More...
Kirk May 08, 2020 for Model Number WDF330PAHW0 When i push start unit will fill with water, but will not do anything after that... just sits... i can push cancel button and unit will drain.
1 Answer Kirk, You will want to check to see if there is power getting to the circulation motor. If the motor is getting power to it then this will be a faulty motor. If there is no power getting to it then this will be a faulty control board. Read More...
Debbie December 19, 2016 for Model Number DU1145XTPBA Unit was working fine and then a couple of days ago the door wouldn't ever shut properly. It wouldn't latch and the handle would barely move. I have disassembled it all and thinking I need to order the actuator? I'm asking because there is absolutely no tension with it and it's loosely moving back and forth within the part# 8524476 - I see no other part that would involve a spring, etc.
1 Answer Debbie, The door latch actuator would be the most likely cause for this issue with the latch not operating properly. Read More...
Scott May 31, 2016 for Model Number KUDS30IVWH In your answer to Denise about the latch actuator on this dishwasher, you mentioned a spring in regard to the actuator. I don't see a spring with the actuator on the parts diagram. I only see a spring on the parts diagram for either side of the handle. Is there a third spring perhaps that connects bottom of the actuator to the latch frame? It seems there is a small arm on each that a spring might attach to. Thanks
1 Answer Hello Scott. The spring is number 4 in the diagram. It is used in the latch assembly. Read More...
Edward October 19, 2015 for Model Number wdf540pabwo serial f43203058 My dishwasher will not run. It starts for 30 seconds cyle lights and stops. The cycle light stays on and nothing happens. I went to LOWES and the same dishwasher was on the floor. I grabbed the handle and it had a leaver spring loaded. My dishwasher doesn't have that. I'm wondering if this needs to be replaced? I purchased the house with the dishwasher. Can you help?
1 Answer Edward, The spring part of the door latch would be what is causing this issue. You would want to replace the door latch assembly WPW10653840. Read More...
Randy October 14, 2015 for Model Number 665.16039401 I have a kenmore 665.16039401 I have to slam the door on my dishwasher a few times before I can get it to run, often it will start then stop this is when I have to shut it hard.
1 Answer Hello Randy. These units have to be perfectly level in order for the door to work properly. If it is level, then check the strike WP8580309 and latch WP8524471 for damage and replace the part that is bad. Read More...
Juergen September 15, 2015 for Model Number GU1200XTLT2 Dishwasher just started by itself the other day. I pressed "cancel" and nothing happened, so I opened the door. NOW, the "pots/pans" cycle light, along with the "cancel" light are just flashing. NOTHING happens when I push any buttons. I turned the power off, and then back on about 1 minute later. Still flashing. About 4 hours later, it turned on by itself again! I opened the door once more and it stopped. BUT, the lights are flashing again and NO button will make it run again. What could that be?
1 Answer Hello Juergen. You will need to order and replace the control panel 8534835 on the unit. Read More...
Denise July 18, 2015 for Model Number KUDI02IRWH2 I replaced the door handle after it was broken and the dishwasher worked once then the second time i went to wash dishes it lost power halfway thru. Any idea what else could be wrong?
1 Answer Denise, You will want to check the latch actuator and check to make sure that the spring is attached and that there is no damage to the latch bolt. This would be the most likely cause for the unit stopping mid cycle with the handle recently being replaced. Read More...