Rwp August 28, 2019 for Model Number WFG374LVS1 need to convert oven back to natural gas looking for spud155 and spud 47 any help would be great
1 Answer RWP,These are the orifices you will need, WPW10170506 for the right rear, WPW10170507 for the center, WPW10170508 for the left rear, WPW10170509 for the left and right front. That takes care of the top burners and you will need to remove the plastic cover off the regulator and flip the screw over, you should be able to read ng on the side facing you. That will convert the bake and broil burners. Read More...
Dave August 15, 2019 for Model Number WFG540H0ES0 I need the bake burner oven spud to convert back to Natural gas for my range WFG540H0ES0 will this work ?
1 Answer Dave, unfortunately, the manufacturer does not list the NG bake orifice separately from the regulator assembly W10919226. Read More...
Dorothy August 15, 2019 for Model Number MGR8800DE0 We are converting our gas range from propane to Natural Gas. During our move we seem to have lost the orifice spuds for the oven. We need the ones marked 46 and 150. Everybody we talked to does not carry these and are saying they do not exist. What can we do? We have found where were you can buy bigger Parts with those spuds in them but not sure what to buy. Can you give us exact item numbers? We would prefer just to get the spuds if at all possible.
1 Answer Dorothy, to replace the natural gas orifices the broil fitting W10583216 and the valve WPW10602004 would be needed. Unfortunately, the manufacturer does not have the natural gas orifices listed as a separate item. Read More...
Ellena March 14, 2019 I am looking for a part number. I have a whirlpool orfice. The only thing on it is 69. Does anyone know a part number. The model number is unreadable.
1 Answer Ellena, Unfortunately without the model number we would not be able to advise on the proper orifice that you would need for your unit. Also we would need to know if you are needing LP or Natural gas. Read More...
Donald July 13, 2018 I need a number 47 orifice spud for the bake in a Maytag model number MGR8700DE0.
1 Answer Hello Donald, I'm sorry but this part 73001045 has been discontinued by the manufacturer and no satisfactory substitutions have been provided. Thank you for your patience and understanding in this matter. Read More...
Kevin November 06, 2017 for Model Number SF195LEHQ5 I need to convert my stove back to natural gas - previous owner didn't keep the original orifices. Is a kit available with all 4 or do I need to spend $120 on orifices compared to $25 to go to propane?
1 Answer Hello Kevin, the only way to convert the unit back to N.G will be to purchase each orifice separate. Thanks! Read More...
Zach September 27, 2017 for Model Number whirlpool wfg114swbo I have a whirlpool wfg114swbo gas range. I need to convert it back to natural gas but I do not have the #47 orifice for the oven burner as the installation instructions call for. Was wondering what the part number for that #47 orifice.
1 Answer Hello Zach, the natural gas orifice for the oven burner is part number W11205068. Hope this helps! Read More...
Michael July 10, 2017 for Model Number SF385PEGQ7 I see the conversion kit only has the spud orifices for the 4 burners. Are spud orifices required for the baking oven, if not, how do I adjust those burners for this Model Whirlpool Range. Thank you, Michael
1 Answer Michael, The bake and broil burner orifices are "adjustable". Oven burner: Use 1/2" combination wrench to turn the orifice hood down snug onto pin (approximately 2 to 2-1/2 turns). DO NOT OVERTIGHTEN. Broil burner : Use 1/2" combination wrench to turn the orifice hood down snug onto pin (approximately 2 to 2-1/2 turns). DO NOT OVERTIGHTEN. Open the air shutter full open, then adjust the air shutter after the burner has ignited and burned for a few minutes, until there are little to no yellow tipping on the flames. Don't forget to save the Nat gas orifices and instructions for future conversion back to Nat gas. Read More...
Chris July 06, 2017 for Model Number Kenmore 148.20126510 I have a Kenmore Grill that was converted to Natural Gas by the previous owner and I need to convert it back to LP, but Sears does not sell a kit for this. The NG orifice spuds I took out were marked 1.37mm and the burners are 12,000 BTU, so I believe the right size would be #59/1.04mm, but am not sure. Any recommendations? I need 5 #59 spuds of the right size.
Jeff April 05, 2017 for Model Number WFG505MOBS Whirlpool 5 burner gas range Need orifice spuds to convert back to natural gas and having trouble finding them.
1 Answer Hello Jeff, You will need to order WPW10347414 for the LF and RF, WPW10170507 for the center, WPW10170508 for the LR, and WPW10170506 for the RR for model WFG505M0BS0. Read More...