Tom October 26, 2013 We have Maytag front load washer machine Neptune model #mah6500aww and will not drain. nd indicator lights up on control panel. How to fix? savfam1
1 Answer Hello Tom, You will need to open the unit and remove the hoses from the pump to ensure no clogs are present. If not, the drain pump WP25001052 will require replacement. Read More...
Mark October 24, 2013 for Model Number Kenmore 11029822800 Hi, I have a Kenmore Washer, Model 800 with Auto Load/Water Level Sensing. When the Washer starts the Normal, Casual or Delicate Cycles, it immediately begins Agitation along with Water Filling. However, when I start the Hand Wash cycle, it starts normally with filling and no agitation, then continues as rest of the cycle. I saw in another post that the load sensors switch W10177795/AP4501024 might be bad. But since mine works on the Hand Wash cycle, do you think this is still the issue? Could it be the Timer or Agitation Delay Board? Thanks Much!
1 Answer Hello Mark. If it fills and agitates at the same time, the timer WPW10187167 is the issue on the unit. Read More...
Dan October 01, 2013 for Model Number mvwc6esww0 My maytag washer has auto fill. It now overfills nobody seems to know what or where the auto fill swich is. Is there one and whats the part number?
Sonya September 17, 2013 for Model Number Kenmore Washer 110.29822800 Washer will not fill up with water but still runs as normal without the water - wondering if it is the auto fill switch and can I replace it myself?
1 Answer Hello Sonya. Yes, you will need to replace the sensor switch WPW10292584. These are easy to replace. Access the inside of the control panel with the power off. Then pull off the knob and unplug wires going to the switch and the hose. Pull upward on the locking tab and twist to remove. Read More...
Scott September 15, 2013 for Model Number MVWC6ESW/W1 The washer spins and then fills with a small amount of water prior to shutting off. Also, rather than filling it starts agitating immediately while filling with water.
1 Answer Hello Scott. You need to replace the sensor switch WPW10292584 and the timer on the unit to repair the unit. Read More...
Karen August 13, 2013 for Model Number Whirlpool washer WTW57ESVW It will start agitating as soon as I turn it on and the water starts but does not fill. Keeps draining as it fills. It done this couple of months ago and just quit. Now it is doing it again.
1 Answer Hello Karen. You will need to order and replace the sensor switch WPW10292584 on the unit. Read More...
Steven July 29, 2013 for Model Number WTW57ESVW0 The agitator begins to spin as soon as the washer is turned on and after a few seconds the water begins to fill the tub while still agitating. Also at the end of the cycle, the machine adds a small amount of water then turns off. I was told that this was an auto sensing switch problem (part # W10292584), does this sound right?
1 Answer Hello Steven. You will need to replace the timer WPW10177827 and the sensor switch WPW10292584 to repair the unit. Read More...
Tracy June 21, 2013 for Model Number WFW9600TA00 Do you have the pressure switch for this model if so how do I order it? Thanks
1 Answer Hello Tracy. Yes, the part number is WPW10415587. You can call 1-877-477-7278 and we will help you place the order over the phone or you can order online. Thanks. Read More...
Tracy June 21, 2013 for Model Number Whirlpool Duet Steam Front Load Washer Need whatever to fix the Error code SUDS then F35. Was told it was a Analog Steam Switch?
1 Answer Hello Tracy. Based on the errors provided, you will need to replace the pressure switch on the unit. Read More...
Bruce May 15, 2013 for Model Number wtw57esvw0 My washer will not let in water, however if you move the dial it will spin. I have already replaced the water valve and flow meter.
1 Answer Hello Bruce. Based on the information you provided, the sensor switch WPW10292584 is bad and will need to be replaced on the unit. Read More...