Gerardo November 11, 2015 for Model Number whirlpool Sorry I can get the exact number of my whirlpool?
1 Answer Hello Gerardo. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. Here is a link to help you locate it. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Sean January 22, 2015 for Model Number lsq9010kq0 Hi what tub size is my whirlpool lsq9010kq0? Is it 3.2 cubic feet?
1 Answer Hello Sean! Unfortunately, we do not have the cu ft information available. Sorry! Read More...
Dave G. January 03, 2015 for Model Number kenmore 80 series direct drive While awaiting the parts I just ordered from you, I decided to clean up the machine and noticed there seems to be water inside the plastic ring on the basket. I noted a plug in the ring. Is this water/liquid part of the balance scheme, or should I pull remove the plug and drain it?
1 Answer Hello Dave, Without the saline solution in the balance ring, the machine will never spin in a balanced configuration. It is necessary for normal operation. Read More...
Marcstumped June 17, 2014 for Model Number WLSE4210A0WW I followed all the directions and removed the tub nut (no easy task) took 5 hours and a lot of muscle. I thought I was home free when I discovered I could not get the spin basket (inner tub) to pull out. All instructions including the one that was inside the machine control panel indicate that once the nut is off, the tub should lift out. Mine isn't. I am clueless what to do now. Please offer any ideas.
1 Answer Marc, Sometimes the spin basket hub WH45X10027 will "stick" to the WH02X10265 split tub bearing due to an over torqued hub nut, or electrolysis or calcification. Sometimes partially filling the tub with hot water and "rocking" the tub side to side or front to back will help break the hub loose and you can lift the tub out. You can also use direct heat (torch), but you have to be extremely careful. Read More...
1 Answer Hello Richard. You will need to contact the manufacturer for this information. Thank you. Read More...
Jason August 08, 2013 for Model Number Whirlpool Mod LSQ 8243 HQ0 I have recieved the inner tub basket. I have removed the agitator. It appears that I have to remove the cabinet top as well. Is it only held with clips or do I have to remove the inner screws at each front corner? They appear hard to get to. Is there anything else to remove? It looks like the spanner nut needs to come of as well.
1 Answer Jason, You will need to remove the cabinet in which to remove the cabinet you will need to raise the control panel and take the 2 clips holding the cabinet out. Once you remove the clips you will lean the cabinet forward and pull off. You will need to take the spanner nut off in order to get the tub out. Read More...
Bill G October 27, 2012 for Model Number lsr8233eq1 I am trying to remove the inner tub, in order to replace the drive block. The tub won't slide off the spindle even though I've taken off the drive block nut. It will move up and down about 1/" to 1/2" and then it catches on something.
1 Answer Hello Bill, If you removed the agitator clip, the washer and the spanner nut then the tub should lift right out. You want to make sure that you have removed the tub ring before trying to lift out or it will only lift about a half inch. To get the tub ring off you will have to take the cabinet off to access tub ring. Read More...
Ricky September 27, 2012 for Model Number 3RLSQ8033SW1 Hi, I have a spin problem with this machine, I have fitted a drive coupling and clutch assembly (both were worn). Still no spin, the agitator spins but the tub doesn't turn. I have noticed, however, that the basket seems to move up and down the shaft so I would assume that it is no longer connected. Do I need to replace the tub?
1 Answer Ricky, You shouldn't need a tub. You my need a new spin tube/basket drive WPW10117003 and or drive block WP21366,WP389140. These components hold the spin basket in position and spin the basket when the washer is in the spin cycle. If you can lift the tub up and down and the tub won't spin, any one of these components could have failed or wore out. You'll need tomremove the agitator, the spanner nut and lift the tub out to check the drive tube and drive block. Read More...
Jim S. November 27, 2011 for Model Number RAS7233KOO After installing a new direct drive coupling(AP3963893)i now have a lot of shaking in the basket, what did I do wrong? I dont have any parts left over and I cant see anything missing or broken.
1 Answer Hello Jim. Check and see if the suspension spring has come off the unit, and make sure the floater plate is centered in the base of the unit. Hope this helps. Read More...