David G July 04, 2020 for Model Number Maytag Model MZD2766GEW Maytag Model MZD2766GEW Refrigerator / Freezer (side-by-side) - buzzing sound when you have the control panel on crushed or cubed ice and depress the actuator to dispense. You have to depress the crushed or cubed ice button to get it to stop.
1 Answer David, This would be caused by a faulty dispenser control board which is part number WP61005274. Read More...
Mickpb September 30, 2019 for Model Number MSD2732grs A buzzing / sizzling sound comes fountain / ice door cover. Randomly starts and stops. Frequently a tap on the cover will stop the noise. As the sound seems to be coming from the relay instead of the ice door solemoid I disconnected the power from the ice door solenoid and shortly there after the noise returned. Is there any other possbile cause than failure of the relay on the solenoid door. The refridgerator is 14 years old so I am not wanting to be throwing parts at it but I quite motivated to get rid of the noise, Thank in advance
1 Answer Hello MickPD, likely the limit switch WP61005520 that is located behind the black rubber actuator pad 61003804 has gotten wet or is failing, which will allow a partial signal to the dispenser control board WP61005274 and cause the noise. Read More...
Buz September 28, 2018 for Model Number MSD2654GRW When selecting Ice or Water the system will stick "ON" and requires multiple pushes of the actuation switch to shut off--often sending lots of ice or water onto the floor--it is getting worse. I replaced the actuator switch and same problem. What is the next most likely part to replace, the control board or the Ice door fountain kit?
1 Answer Buz, This issue would most likely be caused by a faulty dispenser control board WP61005274. Read More...
Bk August 08, 2018 for Model Number MSD2456DEB Maytag Plus MSD2456DEB Two problems. One resolved. 1) Water on floor in front of appliance. Found water and ice under lower basket in freezer and ice buildup in the ‘airway’ leading to the refrigerator section. From a similar experience several years ago, I cut off power, emptied freezer & refrigerator and let unit totally defrost. After cleaning the interior, I reconnected power and, when satisfied things were working properly, reloaded food in both sides. (Resolved) 2) An hour or so later, I tried to get a glass of ice and water from the dispenser and discovered nothing related to the dispenser was functional. No lights. No response. No nothing. I tried the lock/unlock feature. Nothing. Selected the various control buttons. Nothing. Replaced the dispenser’s light bulb. Nothing. Tried resetting things by disconnecting power and reconnecting after 30 seconds. Nothing. (Problem!) All other features of the refrigerator and freezer are working as they should. Time to replace the dispenser control board?
1 Answer BK, More likely you have a fountain switch issue going on.Part# WP61005277 is the fountain switch.Remove front cover and check to see if you have voltage from the control to the fountain switch.board Read More...
Sarg November 04, 2017 for Model Number MF12067AES Water/Ice dispenser light will not come on. Everything else works fine. Is there a bulb or is this an LED issue with the control board.
1 Answer Sarg, There is no bulb for the dispenser light, it is an LED system and is mounted to the chute extension assembly WPW10131128 . Power to the LED lights is supplied by the low voltage/dispenser control board. Read More...
Terry May 02, 2017 for Model Number MZD2766GEW Ice maker woes. Have replaced icemaker completely 3 times. Have replaced all valves twice over the past 6 years. Ice maker now is very erratic. Sometimes works great, most times either too much water in maker causing the cubes to fuse together and hang or no water and not makes ice. always over flows maker and freezes in the bottom of bin. have had to replace auger, bin and motor over the past couple of years. Bin support is now broken for the second time. Any ideas?
1 Answer Terry, With the icemaker overfilling then this would most likely be an issue with the water valve that is not fully closing or too high of water pressure. Read More...
Thomas October 26, 2015 for Model Number MSD2756GEW The water dispenser quit working on our fridge. I don't see a switch in the parts breakdown. Does the control board operate the water dispenser? Thanks
1 Answer Thomas, Yes, the dispenser control board WP61005274 supplies power/voltage to the water dispenser solenoids. But, your first check should be at the reservoir, make sure it's not frozen or clogged. Then check the water inlet valve(s) on the back of the refrigerator. The valve(s) are more susceptible to failure than the control board, under the circumstances. Read More...
Steve August 20, 2015 for Model Number maytag MSD2756DE What would cause the ice maker and water dispenser not to dispense either? The ice maker is making ice
1 Answer Hello Steve. Make sure the dispenser is no locked. If not, then you will need to check the actuator pad and the micro-switch WP61005520 in the dispenser and see if it is bad. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Chris August 14, 2015 for Model Number Jenn-Air JCD2389GES Ice maker stopped filling with water. Line clear, pressure good, water still flowing through water dispenser on door. Replaced valve/solenoid and problem persists. Replaced icemaker, problem persists. Likely issue? Faulty control board? Only other symptom is water occasionally delays shut off if filling glass in door, etc.
1 Answer Chris, The most likely cause for the water to not get to the icemaker when the icemaker has been replaced and the water valve having been replaced would be a frozen fill tube to the icemaker. Check to see if the fill tube is frozen and clear. Read More...
Charlie June 21, 2015 for Model Number MSD2656DEB The water on the outside door panel would not shut off. Finally, the water stopped running, however, now the light on the front door constantly stays on. When I push the button to dispense crushed or cubes, the green light above "crushed" or "cubed" comes on, however, nothing works. I am unable to dispense ice or water and the light stays on. Do I need to replace the switch? It seems to have gotten pretty wet from the water running.
1 Answer Hello Charlie. It sounds like the board WP61005274 and the micro switch WP61005520 may be bad and need to be replaced on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...