Jj January 18, 2015 for Model Number wtw8240yw0 The Bleach and detergent reservoir overflow. They are not plugged and are the two drain port model.
1 Answer JJ, For the bleach and detergent reservoir to overflow on this model the unit would have to have some type of clog either in the dispenser or in the tub cover area. Read More...
Lyndee December 08, 2014 for Model Number GHW9100LW0 The lights on the control panel of our washer-display and indicator-flash, flicker, or don't light at all. The display window light has a red line in it that is on all the time. It still runs through the cycles Okay and if I depress the amount of time button in, it will actually let me choose all the preferance's like it normally would (spin speed, h2o temperature, extra rinse, etc...). Any ideas on what may be going on? Thanks
1 Answer Hello Lyndee, This sounds like an issue with the user interface WP8181905. If it were an issue with the control board it would be more likely to cause cycling issues. Read More...
Richard H November 06, 2014 for Model Number 11044936203 What is the HE2 terminal for on the control module? We have wires going to this terminal, but in your video you did not have one.
Amberly82 October 07, 2014 We have a whirlpool duet frontload washer purchased in 2011. The washer has been working great and then all of a sudden had some random errors. We located a broken wire and repaired it but now we continue to receive a f7e1 error. The confusing part is that the washer will go through the entire cycle empty but if you add even a small load of clothes it will error. Any help would be appreciated.
1 Answer Hello Amberly82. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Tere July 31, 2014 for Model Number GHW9100LW2 We had a rare electrical storm in San Diego, and our power went out (never happens). The duet front loader we have had since 2004 had been periodically stalling to restart when using "add a garment" recently. After the power was restored, the panel and controls went dead. No lights, no controls, nothing. I checked the curcuit breaker and it did not pop, but I tried flipping it on and off anyway just in case. The grounded outlet is fine. The dryer works on both plugs and I tested a seperate 110 V electrical appliance also and it works fine. Is this the User interface or the Control Board, or something else?
1 Answer Tere, The first thing that you would want to check would be the line filter where the power cord plugs into on the unit. Check for 120 vac coming into and out of the line filter. If there is power into the line filter but no power out then the line filter WPW10367632 is bad and would need to be replaced. If there is power into and out of the filter then check the main control board for voltage into it. If there is power in then the control board WP8182221 is faulty and would need to be replaced. Read More...
Wizzle A. July 29, 2014 for Model Number GHW9100LW2 Washer works fine except towards the end of the cycle it stays stuck in final rinse mode showing it has 1 minute left in the cycle and it takes about 20 minutes to finally time out. What could be wrong?
1 Answer Hello Wizzle, This sounds like you need to run the diagnostic test. The tech sheet explains this as follows: Starting the test modeClose the door.Press the Control On button.Select the DRAIN/SPIN cycle.Select NO SPIN by pressing the SPIN SELECT button, as needed.Push Prewash Option button four (4) times within five (5) seconds. C:00 will show in the display.NOTE: If Model does not have PREWASH Mode as an option, press RINSE/HOLD.If the Starting procedure fails, push PAUSE/CANCEL button. Then repeat the starting sequence. If fault codes are detected, they will be displayed. This gives you a starting point to troubleshoot from. Read More...
Lester D. July 08, 2014 for Model Number ghw9100lw2 Getting f06 error code checked wiring connections at mcu and motor appear to be ok have run dia. check 3 times never shows problem with the diagnostic test. only when using does it show up f06
1 Answer Lester, With the units wiring checking ok and all working in the diagnostic then the issue would most likely be in the Central control unit WP8182221. Read More...
Daedge2 February 23, 2014 for Model Number GHW9400PL1 When I run the diagnostics, it will flash F then H then goes back to time 002. The CCU seems to be making a hissing noise. When I unplug the CCU it will quit. I do not hear any click like it says I am suppose to hear. I want to make sure it is the CCU before getting one they are costly.
1 Answer Daedge2, The "FH" error code indicates that the washer isn't filling with water properly or the water level switch is not "tripping" between empty and full. The lack of cold water could be the issue, and causes the diagnostics to stop at the 002 segment of the test mode as well as the hissing noise. When power to the CCU is first established, there may be a "faint" click noise from the board itself. it can be very faint and may not be heard. But the fact that the control can be programmed, tested and display works, tells you the line relay closes and the board operates. You would want to recheck all the diagnostic codes, check the fill valve and water supply to the washer, and the water level switch and air tube, before you replace any other parts. Read More...
Jim February 08, 2014 for Model Number GHW9100W2 I have a Whirlpool front loader GHW9100W2. I was getting an FH code at random times. I went into the diagnostic mode and ran all the tests. The hot fill would error out. I replaced the inlet valve and retested. The error came back so I purchased a CCU from Appliance Parts Pro and installed it. As soon as I plug the machine in I hear a squeal come from the control box and the control lock light is on. I tried pressing the cancel button 2 times to reset the controller but it will not reset. The boxex look identical but the original box has the number el:06222 and the new box has the number el:06223. Not sure if this is the correct box or I have another issue?
1 Answer Jim, Based on the model number the correct part number for your main control board is WP8182221. This is the part number that should be on the box that you received. If it is correct and the display is making a squealing noise then double check all the connections to make sure that they are fully seated and in the correct positions. If this checks ok it is possible that the control board is faulty. Read More...
Charles May 17, 2013 for Model Number GHW9100LW I have a duet washer that I keep getting a F02 error code. I have checked drain hose, replaced pump. I had a repairman check unit and he suggested replacing motor control unit. The error occurs just prior to spin cycle.
1 Answer Charles, With checking the pump and the drain hose, since they are clear and you have a new pump, you would want to check to make sure that the wire connections are not bad. If they check ok then the control board would be the most likely cause. Read More...