Mark April 06, 2013 for Model Number WFW9200SQ01 Keep getting error code f28. Can't get anyone to tell me what it means or how to fix it. If you can help me with this code I would greatly appreciated it thank you
1 Answer Mark, The F28 error code indicates a serial communication error between the Central Control unit (CCU) and Motor Control Unit (MCU). Possible causes and procedure, Unplug washer or disconnect power. Check the wire harness connections to the MCU, the motor, and the CCU. Check connections of the CCU board within the housing. Make sure that all grounding switches are engaged. Check the drive system for any worn or failed components. Plug in the washer or reconnect power. Verify CCU operation by running a Diagnostic test or any cycle. Check the MCU by looking for operations of the drive motor. Check the drive motor for powered rotations and check that the serial harness at the MCU is not mounted upside down. The wires should be to the left when facing the MCU connectors. Look for corrosion on the wires and clean with alcohol where necessary. Read More...
Jz April 02, 2013 for Model Number GHW9100LW2 My Duet Whirlpool washer stops half way through almost every cycle with an F02 code. If I hit stop and start real quick the cycle will most of the time keep going and finish without a problem (other times it resets the cycle but then, still finished without issue). Very annoying. I put it into diagnostic mode and it gave an F-02 in part 6 of the cycle (expected), but then I ran it a couple more times and it worked fine. Checked for cloggs in the drain pipe and drain filter. Checked for 15 ohms on drain pump and it was replaced about 1 or 2 years ago for this same issue. Could this be a bad CCU? Does this go bad often? I would hate to spend $200+ if this is not the fix. Any advice is appreciated. Thank you!! JZ
1 Answer JZ, Make sure that you also check the pressure hose to make sure that it is not clogged and check the hose coming off the bottom of the tub to make sure that it is not clogged. If either are clogged it could cause longer drain. If these check ok then you would want to replace the pump 280187. Read More...
Chuck I December 30, 2012 for Model Number GHW9100lw1 I get cold water at start of fill cycle then when it adds water during wash cycle it adds hot water only , no matter what temp. you have set for the wash cycle?? Used to fill with cold on a cold setting and hot on a hot or warm wash setting . Now I get hot no matter what setting. Hoses and supply lines are good as well as screens and inlet valve. I do get cold on the rinse settings . If I shut off hot water supply so That only cold can get it in , it will hum at the dispenser like it is trying to add hot water during the wash cycle. IT does this on any wash setting. Bad inlet valve or ccu ??
1 Answer Hello Chuck, You will want to check the thermistor. At the control board with unit unplugged at room temperature you will want to do a resistance check of the thermistor. here are the resistance readings that you should have: Temp. Results32°F / 0°C/ 35.9K O86°F / 30°C/ 9.K O104°F / 40°C/ 6.6K O122°F / 50°C/ 4.6K O140°F / 60°C/ 3.2K O158°F / 71°C/ 2.3K O203°F / 96°C/ 1K OIf you are outside of these ranges then you would need to replace the thermistor WPW10467289. Read More...
Chuck December 23, 2012 for Model Number GHW9100lw1 Machine will add cold water to start load cycle then as it needs to add water it will only add hot water even if the load controls are set for cold wash and cold rinse. If you shut off the hot water supply it will not add any water at all. I have pulled water supply lines loose and checked for obstructions at the fill valve screens and hoses. All is open and free flowing there, would the dual fill valve be bad possibly only on the cold water side? The only way we get any cold water in the machine after initial cold water fill on any load setting is to set machine to rinse and spin only. Showed an error code one time of HF before pulling hoses and cleaning screens and have'nt had that show since, but still not getting cold water added to any wash cycle?
1 Answer Hello Chuck, You would want to check the water temperature sensor to make sure that it is good. If the temperature sensor checks ok then you would want to check the wiring to CCU and to valve. Here are the value and how to check temperature sensor.Water Temperature SensorDisconnect the wire harness fromthe water temperature sensor andmeasure the resistance of thesensor. Use the following table.An abnormal condition is an opencircuit.Temp. Results32°F / 0°C 35.9K O86°F / 30°C 9.K O104°F / 40°C 6.6K O122°F / 50°C 4.6K O140°F / 60°C 3.2K O158°F / 71°C 2.3K O203°F / 96°C 1K O Read More...
Joe December 06, 2012 I have duet washer GHW9100LQ1, the dial light on the control panel is blinking, wont accept the start. I tried to go through diagnostic wont go through diagnostic...
1 Answer Hello Joe. You need to check for a stuck button. If none is found, then you will need to replace the user interface WP8181905 on the unit. Read More...
Don November 25, 2012 for Model Number ghw9100lw1 Problems with my whirlpool duet front loader. Started getting an f09 error and once this happened hot water just keeps filling the machine. I can shut the supply, and unplug the machine. Restart with just drain and spin and it will finish fine. Replaced the drain pump and checked for obstructions in the drain hose. Now I'm getting an f/h error on most loads and a couple of times it actually ran through the cycle, the hot water starts filling after it lights up cycle complete and turns off. The only way to stop the filling is to close the hot water supply completely and then open it back up. Any suggestions?
1 Answer Hello Don. Based on the information you provided, it sounds like the water valve is bad and will need to be replaced. Read More...
Greg November 20, 2012 for Model Number Whirlpool Duet Washer GWH9150PW1 My washer won't spin or drain and I get error code F11. Is this the motor control board? If so, what is the part number for the replacement part? Is this a difficult part to replace?
1 Answer Hello Greg, Check all connection from motor to MCU and from MCU to CCU. If they are good then you would want to replace the MCU W10756692. Read More...
Bob November 17, 2012 for Model Number GHW9150PWO I have a Whirlpool Duet washing machine 6years old that gives a 'dl' door lock error. I can hear the clicking sound it makes 6 times before throwing the error. I replaced the door switch assembly but this didn't solve the problem. I assumed that hearing the clicking sound was a relay activating. Looking at a schematic a see a relay that connects to the heating element via the main switch inside the door switch assembly. Is this my problem or am I way off course?
1 Answer Hello Bob. No, if the lock assembly has been replaced, you either have a bad wiring harness, or the control board is bad and will need to be replaced. Also, make sure the latch strike on the unit is not broken. Read More...
Brooke S. November 14, 2012 for Model Number GHW9100LW1 My washing machine will not work. The lights will not come on as if it has no power. The breaker did not kick, the reset button on outlet has been reset, the door is closed all the way. What could be the problem? Thank you.
1 Answer Hello Brooke. Test for power to the user interface. If there is power there, and the unit does not light up, you will need to replace the interface WP8181905. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Don September 12, 2012 for Model Number WFW8500SR00 I have a whirlpool duet Model WFW8500SR00 I have a code of F-30 which says it is the dispenser switch/motor, I have changed it with new one it still just rotates and does not stop on a setting in wash modes. The after a time it flashes code. It will operate in rinse/spin cycle though
1 Answer Don, Before you replace a control board, Check or replace the linkage assembly parts for the dispenser : WP8540393, WP8540394, WP8540395. Check and make sure there are no frayed or loose wire connections between the dispenser motor and the CCU. Check and make sure the diverter is not defective, hanging up, moves freely etc. Then conduct the manual test or the diagnostics overview test and check the dispenser operation. Read More...