Cs February 17, 2023 for Model Number GHW9100LQ1 The washer goes into one of the drain/spin modes during a full wash cycle, then shuts off and starts beeping and flashing F2. We've checked the drain lines for clogs, but they're clear. When we push 'PAUSE", then "START", it proceeds normally with the cycle. It may stop again for the F2, or may complete the cycle normally. No pattern on when it will stop. Is this a draining issue, or a control board?
1 Answer CS, Thanks for asking!!! It is likely that the drain pump is failing and needs to be replaced. You can check for voltage to the pump when it should be running. No voltage replace the control. Voltage present and water not draining replace the pump 280187 (only after verifying there are no blockages. Sometimes a coin can act like a valve and swing at random to block one time and allow flow the next.) Read More...
Ron May 06, 2021 for Model Number GHW9100LW1 Whirlpool Duet Washer (GHW9100LW1) kept giving F02 code. Cleaned all lines and replaced the drain pump assembly. Pump works it drained all water from machine, but when try to start a new cycle it keeps trying to drain and there is no water to drain. Have tried to reset by unplugging from power source for anywhere from 5 minutes to 5 hours. Any suggestions?
1 Answer Ron, it would be recommended that the pressure hose WPW10004260 is checked for a partial clog where it connects into the tub. If there is not a partial clog, it would be likely that the pressure sensor WPW10514214 has failed. Read More...
Rob November 15, 2020 for Model Number GHW9100LW1 My washing machine will not start. I have narrowed it down to either the door switch or control board. It powers up fine. When trying to start it, you push the start button but the door never locks, so the cycle does not start. . I do not hear the "thud" of the locking mechanism. The problem has been intermittent. Sometimes nudging the door with a knee helped or holding the button for up to a minute. I ran the diagnostics and nothing came up wrong. The door locked during the test sequence. I would rather not buy both parts. How can I tell which to replace?
1 Answer Hello Rob,the control has to see the door closed through the door switch before it will allow it to lock, the door latch lock/unlock solenoids are powered by the main control board latch relays, the latch is part WP8182634 if after the latch is replaced it still having a problem then the main control board WP8182221 will need to be replaced next. Read More...
Peter November 10, 2020 for Model Number GHW9400PW0 Keep getting a FH code. Cleaned the strainer and replaced the hoses.
1 Answer Hello Peter, the FH code refers to the main control board not seeing the washer filling fast enough. It checks this 2 ways, if the water flow entering the tub during fill is ok, then if the code shows in about a minute or under then replace the flowmeter WPW10110225, if the code shows after about 8 minutes then replace the pressure switch WPW10514214 and airline tubing WPW10004260. Read More...
Robert Ziegler Jr August 19, 2017 for Model Number GHW9100LW2 Whirlpool Duet Washer GHW9100LW2. Bad control board or user interface assy? Dial on hand wash-LED flashes (30), on delicate- LED flashes (35), on normal- del LED flashes (35), on HD- hand wash LED flashes (30), on white whites- no LEDs – read out (dash dash dash)
1 Answer Robert, This issue sounds like it would be caused by the main control board of the unit. The part number would be WP8182221. Read More...
R.F. December 15, 2016 for Model Number GHW9200LW0 I just replaced the front control panel with one I received from you. When I push the Control On button the light for my selected cycle blinks. I push and hold Start and nothing happens. I don't hear the door lock solenoid click. I checked all the connections and nothing seems amiss.
1 Answer Hello R.F., You should pull the tech sheet and run a diagnostic test to pull any stored fault codes. The procedure is as follows:Starting the Test Mode Close the door. Push CONTROL/ON (if present on this model). Select the DRAIN/SPIN cycle. Select NO SPIN by pressing the SPIN SPEED touchpad. Push PREWASH OPTION four times within five seconds. (If PREWASH OPTION is not present on this model, press RINSE HOLD four times within five seconds.) C:00 will light up on the display. If the Starting procedure fails, push the PAUSE/CANCEL touchpad, then repeat the starting procedure.Test Program ControlIn order to advance to the next step of the test procedure, push PREWASH OPTION touchpad two times. If PREWASH OPTION is not present on this model, press RINSE HOLD two times. Read More...
1 Answer Hello Lonnie. Remove the top off the unit to access the pressure switch. It is on the side of the cabinet. Read More...
Anthony January 18, 2016 for Model Number GHW9150PW4 Here my problem. I Start any cycle and it functions normally, one the rinse cycle tries to start I get a the minutes left flash and try to restart 3 times then an f06 error at that point I cancel the cycle and try to start a new cycle and it will not even wash and I get the same minutes flash and 3 X cycle restart f06 error. I try to run the diagnostic mode and it goes from c01 to c03 in a few minutes filling with water and then the diagnostic mode stops and a 002 flashes and nothing else happens. I unplug the unit you here some buzzes and clicks by the motor control and restart the unit 002 is still flashing hit cancel and start the cycle again and it goes through a complete cycle no problem run the diagnostic goes through the complete cycle no problems and start another load and it starts all over again . do you think its the CCU? or the MCU?
1 Answer Hello Anthony. Possible Causes / Procedure1. Verify the shipping system including shipping bolts,spacers and cables are removed.2. Unplug washer or disconnect power.3. Check wire harness connections between the drivemotor and the Motor Control Unit (MCU), and betweenthe MCU and the Central Control Unit (CCU).4. Plug in washer or reconnect power.5. Check the MCU by looking for operations of the drivemotor.6. Check the drive motor for powered rotations. Read More...
Paul T October 10, 2015 for Model Number GHW9100LW1 Door Solenoid does not pick up when Hold to Start button depressed. I tried to run through the diagnostic check but does not start routine when following procedure. Also found in manual that the CCU should hear a "click" when power is removed and reapplied. I tried several time both diagnostics and power cycle but no success. Everything on front panel lights up properly. However I did have to replace the front panel several weeks ago because of worn out button "hoods". Purchased unit from on-line supplier and has works several weeks before this problem came up. Not sure if this front panel caused problem or just coincidence. Wanted to make sure before purchasing $250.00 CCU.
1 Answer Paul, With the unit not going into the diagnostics then this would most likely be a faulty CCU but double check all wire harness connections to make sure that there are no loose connections. Read More...
Dave May 24, 2015 for Model Number GHW9300PW4 Had GHW9300PW4 washer running and left house (wife might have Paused, don't remember). Came back in and washer is giving a steady beep with all the indicator lights lit up for the OPTIONS, WATER TEMP, SPIN SPEED, and END OF CYCLE. Display itself is blank. Unplugged for a few seconds, plugged back in and it "steady beeps" again with same indicators all lit. Left unplugged for a longer time, and plugging back in everything is blank until I press the Control ON button, and then the steady beep returns and same indicator lights all light up. I can Spin the selector knob, and the type of wash selectors each light up in turn as I rotate from one type of wash condition selection to the next. Display stays blank through all this, and pressing any other buttons does nothing, so not able to get to diagnostic mode. What else should I check? What is most likely wrong? CCU, UI, other? Thanks in advance, Dave
1 Answer Dave, The most likely cause for this issue would be a faulty CCU. With the unit resetting and then doing the same thing all over again there is a issue with the CCU and would need to be replaced. Read More...