Joe January 04, 2012 for Model Number GHW9100 When the washer is plugged in, door shut, select cycle, press on the panel lights up, press start nothing happens. No error codes no sounds, press cancel lights shut off. Could it be the door lock?
1 Answer Hello Joe. Test and see if there is power coming to the door lock WP8182634 when the start button is pressed. If no, it sounds like the control WP8181905 is bad and may need to be replaced. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Joe D. December 05, 2011 for Model Number ghw9150pw0 When door is closed, timer light is on and control light, but when you press start, it will not start. The door is completely closed. Is the problem with the door switch or the control board? Need help wife need me to fix asap.
1 Answer Hello Joe. Test and see if the control is sending power to the door lock assembly. If not, you will need to replace the electronic control WP8182785. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Debra October 04, 2011 for Model Number GHW9150PW1 Have a whirlpool duet front loader It started like there was no power after checking the breakers and plug.I changed the ccu and got power back on. When starting the cycle it ran for about 3 min and now I am getting a F H error. Whitch is water level. Now it has water in it and will not do any thing lights up timer is on but will not start door will not open I can hold cancle and it will power off but the door will not unlock and it will not go into a sipn/Drain or nothing can u help me please. I have had more trouble out of these than what they are worth. I have 2 kids and a husband, I also work full time I do not have time for the laundry mat PLEASE HELP?
1 Answer Hello Debra. Check and make sure the wires are connected good in the unit. If so, and the code continues, you will need to replace the pressure switch WPW10514214. Hope this helps. Read More...
Todd W. October 02, 2011 for Model Number GHW9150PW1 The only lights that light up are the delayed wash and extra rinse. When I unplug it I hear it click in the ccu but nothing on the control pad works or lights. Can I do any checks on it? Dont know if its the ccu or the pad ?
1 Answer Hi Todd. Remove power . Remove top and back cover. Inspect all buttons door switch , fill hoses, inlet valve screens, all connections, door switch. Access the Tech sheet folded inside in a cover. Are any buttons stuck? The ccu is part # WP8182221. Thank you. Read More...
Dave September 27, 2011 for Model Number 8182695 - Whirlpool GHW9150PW The part number you shown is 8182695, but the part number on my Bitron Control shows el:20711 or 857008297000. Did they change part numbers and will the new 8182695 work?
1 Answer Hello Dave! If you are needing the central control unit on Whirlpool GHW9150PW model is part number WP8182695. Thanks. Read More...
Chris D September 01, 2011 for Model Number GHW9150PW0 I recently had a F11 error code on my Whirlpool Duet washing machine. After reading I knew it was 1 of 3 components. It was either the CCU, MCU or Motor. I ordered the CCU nope did not fix the problem so I ordered the MCU and motor from you. I changed the MCU and the washer now works perfectly. My Tech question is as follows. If this happens again how do I know if it is the CCU, MCU or the motor. I have an OHM meter so this should be easy to check but not exactly sure where to check it at. If you could provide this information it might help in people not buying and returning parts they dont need like I did. Your customer service department is top notch very helpful and friendly. Your prices are great and my overall experience with your company has been a 5 star experience.
1 Answer Hello Chris. The best way to tell which part is bad, is to test for power. You will test for power at the motor. If there is none, then you got to the MCU. If there is power coming to the MCU, but not out of the MCU, you will need to replace the MCU. If no power is coming to the MCU, you will replace the CCU. Hope this helps. Read More...
Ted M. June 17, 2011 for Model Number ghw9250ml2 How do I test the door lock switch assembly and control board to see which one is bad? Im getting error code DL F.
1 Answer Hello Ted. You will need to test and see if your getting power to the lock assembly WP8182634. If there is power there and the door does not lock, you will need to replace the door lock assembly. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
1 Answer Hello. The DL error on Whirlpool unit's is typically either a door lock failure WP8182634, or a failed CCU board WP8182695. These parts can be tested using a multi meter MA-DM1. I will include a link in this message to an article that details how to test various parts with a meter. I hope this info helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Paul D. May 14, 2011 for Model Number GHW9150PW0 F11 on my duet comes on I unplug washer, it works for awhile. Then comes back on.
1 Answer Hello Paul! Here is the information from our error code page: F11 indicates a serial communication error. Communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly. Potential Causes: • Check Wire Harness connections to the MCU, the motor, and Central Control Unit (CCU) • Check the Drive system for any worn or failed components • Check MCU • Check CCU • Check Motor • Check Wire Harness Replace failed component. Hope this helps! Read More...
Matt May 10, 2011 for Model Number ghw9150pw2 My Whpl Duet keeps giving me the F6 signal every time I start a load and will not continue. I noticed a small flash from one of the relays when I push the start button. Is this normal?
1 Answer Hello Matt! Is it an F6 or an F06 failure code? If it is an F06 failure code please see the following link to help verify and diagnose the issues, thanks! http://www.appliancepartspros.com/repairtips/repairtips_appliance+fault+codes.aspx#Whirlpool%20Duet%20Front%20Loading%20Automatic%20Washer%20Fault%20Codes Read More...