Pickledoldman June 23, 2011 for Model Number GS6NBEXRQ01 Replaced the IM control module. No water going to tray. Replaced inlet valve. Still nothing. Ejector arm turns but no water to tray.
1 Answer Hello Pickledoldman. You will need to check and see if the fill tube is frozen. If so, you will need to thaw out the fill tube so water can come in when the icemaker cycles. Hope this helps. Read More...
Enda K. June 17, 2011 for Model Number Whirlpool Fridge with ice maker & dispensor on door Ice maker stopped working and upon inspection discovered the white cog wheel on the control module on the side of the ice maker has broken. Can I replace the cog wheel, without changing the control module?
1 Answer Hello Enda. No, they do not sell just the cog wheel. You will need to replace the module. Hope this helps. Read More...
Jim June 15, 2011 for Model Number KitchenAid 25 cu ft side-by-side refrig/freezer with optical sensors Ice maker stopped working through a full cycle. Water goes in the mold. The water freezes. But the ejector tongs stop when they rotate to the ice cubes still in the mold. The heater works as the ice cubes come loose but then re-freeze to the mold. I don't know if the heater is out of sync with the ejector cycle or if the motor is too week. Or something else? Any help would be greatly appreciated.
1 Answer Hello Jim. Based on the information you provided, it sounds like the icemaker 2198597 is bad and will need to be replaced. Hope this helps. Read More...
Rick V. June 11, 2011 for Model Number ksrs27cnbl00 Is this the right ice maker for my model KSRS27CNBL00?
1 Answer Hello Rick. The icemaker for your model is indeed the 2198597. I hope this info helps! Read More...
George F. June 10, 2011 for Model Number KSRG25FKBT04 Kitchen Aid Is this the right ice maker for model KSRG25FKBT04?
1 Answer Hello George! Yes, 2198597 is the right replacement ice maker for your model. Thank you for choosing us! Read More...
Jeff May 24, 2011 for Model Number 106.56712500 Does the complete icemaker assembly come with the ice maker control module? I removed the complete assembly, defrosted, reinstalled. The icemaker made one batch of ice cubes then quit functioning again. Does the complete icemaker assembly sound like a logical solution? Or would you recommend just the control module?
1 Answer Hello Jeff. It sounds like the icemaker is bad, and will need to be replaced. The icemaker assembly 2198597 does come with the module. Hope this helps. Read More...
Jj May 16, 2011 for Model Number (same model Number as my 1st post) It's the same model number as from my 1st post. (not near the fridge so I can't get it right now) I have heard of some people sanding down the ice tray and then spraying with extreme temperature appliance paint, I may have to try something like that because I really don't want to pay for the entire assembly when it works fine.. just because whirlpool made a tray coating that only lasted 2-3 years, sad. (fridge is only 5 years old)
1 Answer Hello JJ. You can order just the mold WPW10190929. You do not have to order the complete icemaker. Hope this helps. Read More...
Jj May 16, 2011 for Model Number N/A Why would I replace the Ice maker if it works fine... I just need some sort of spray to coat the existing one so that the ice does not taste bad due to the peeling of the coating.. Also I do not need the whole assembly if it's just the ice tray, what is the part for just the ice tray or a spray coating, thank you!
Jj May 15, 2011 for Model Number Whirlpool ET1CHMXKB05 Ice maker works great but the coating on it is peeling off, is there a spray to re-coat it so that the bare metal is not exposed as I believe it is making the ice taste funny.
1 Answer Hello JJ! If the coating is coming off, the icemaker will need to be replaced. Your part number is 4317943. Thanks! Read More...
Douglas L. May 07, 2011 for Model Number WHIRLPOOL Complete icemaker assembly (8 cube) (Part Number: AP3182733 Just purchased from appliance parts pros icemaker, I am on well water and the pressure is lower that city water. Is ther a way to adjust the fill to allow more time for the water to fill the tray? Currently it fills 1/4 to 1/2.
1 Answer Hello Douglas. Yes, there is a small white plastic screw on the side of the module. You can use this screw to adjust the water level. Do not turn it to much. A little is alot of difference. Hope this helps. Read More...