Bob B June 01, 2025 for Model Number kenmore coldspot 10671209101 Hello, i am trying to replace part # 2212964 and the start device kit 8201769 is showing as the replacement. 2212964 has a wiring harness attachment but 8201769 does not. Do you have a video showing how to install this correctly? I read on previous posts that " The red wire would go to the overload, the white wire would go to the bottom left terminal of the relay, and the blue wire would go to the bottom right terminal of the relay." but a visual would be much more beneficial if possible before i purchase this. Please and thank you
1 Answer Bob, Thank you for your question. The white wires will attach to the relay on pin number 2 and the red wire will go to the overload. Read More...
Carlos April 12, 2023 for Model Number KTRC22EKSS00 I have purchased kit for EGY60 Compressor, part numbers 282402 or 403 are my choices, I don't know which to use.
1 Answer Carlos, Be sure you are looking at the part number on the overloads, as per the manufacturer instructions: Install the new overload protector for your compressor type as described below: • EMU60 & EGY70 use part 2154760 or the • EGY60 uses part 2214067 Read More...
John November 29, 2021 for Model Number GR2SHKXKT00 Whirlpool model#GR2SHKXKT00, compressor model#EGY 60HLP. original part#2213105. Whirlpool said it was replaced with part#8201769. from the photo for this part, it seems have only 2 pins but the original part has 3 pins (blue&white connect to 12uf capacitor, red to the overload in the start kit). how to connect the 3 wires to this part#8201769?
1 Answer Hello John, this is the correct compressor start device for your model, wiring connections are covered in the instruction sheet that comes with the kit Read More...
Tony July 16, 2020 for Model Number IKT196301 I have an Inglis refrigerator, model# IKT196301 with compressor model# EMY 60HSC. I have the kit 8201769. Can you tell me the actual terminal numbers where the red, white and capacitor go? I understand that one side of the cap has to go to neutral in. Thank-you.
1 Answer Tony, the red wire will go to the overload protector, the capacitor will be wired into terminal 2 and 4, and the incoming neutral wire will go to the last terminal. Read More...
Tony July 15, 2020 for Model Number IKT196301 I have an Inglis refrigerator, model# IKT196301 with compressor model# EMY 60HSC. I have the kit 8201769. I've read conflicting instructions on here on where to hook up the capacitor. I only have the single connector with the red and white wires. That makes sense to me where they go. But to which terminals do I hook up the start capacitor? And is the capacitor polarity sensitive or does it matter which terminal on the capacitor goes where? Thank-you.
1 Answer Tony, the capacitor would have to be wired into the circuit using a 14 gauge stranded wire and an insulated terminal. The added wire would go from the capacitor to the right-hand terminal of the relay. The other side of the capacitor would be wired into neutral. The capacitor is not showing as being polar sensitive. Read More...
Vin July 07, 2020 for Model Number kenmore 106.61284102 Kenmore 106.61284102 compressor EMY70HLP original part 3ARR55M4F1A / 2212964 capacitor 2169373 (12uF) Totally confused. The replacement part 8201769 is nothing like the original part. Can you upload or send me the instructions please? The two videos above are helpful, but this part is different. I don't know if I can reuse the old capacitor or if I need to order a new one for the new part. Thank you.
Vin July 06, 2020 for Model Number Kenmore 106.61284102 Refrigerator One the original part 2212964, what is the two-wire plug-in connector type? I'm trying to find the right parts to connect to the existing wiring harness.
1 Answer Vin, on the compressor start device kit 8201769, the red wire will go to the overload with the plastic connector having the white wire on the bottom so that the adapter wire will fit in place. If there is a capacitor used, the blue wire would connect to the right terminal of the start relay. Read More...
Krish K. July 03, 2020 for Model Number Compressor EMY60HSC How do I fix one of the burned terminals on the compressor EMY60HSC? The terminal has thinned out and the overload relay sits loosely on the terminal.
1 Answer Hello Krish, I'm sorry but the only fix for a burned terminal on the compressor is replacing the compressor. Read More...
Krishkay July 03, 2020 for Model Number ET8MTKXKQ01 Fridge model ET8MTKXKQ01. Compressor EMY60HSC Which overload relay to use: 2214067 or 2154760
1 Answer Krishkay, the overload 2214067 would need to be used from the start device kit 8201769 for the model and compressor type provided. Read More...
Krish K. July 02, 2020 for Model Number ET8MTKXKQ01 My refrigerator has Compressor number EMY60HSC. Which overload relay should I use 2214067 (282403) or 2154760 (282402)? The three pins on the compressor are upside down: the single pin on top and the two pins at the bottom. Where should the white wire be connected, the left, or the right pin? Remember the pins are upside down than the ones shown in many videos. Which wires should go to the capacitor? This is URGENT, please. My refrigerator is down. Thank You
1 Answer Hello Krish, The Red wire connects to the overload which is the center terminal. The white wire should connect to the right pin which should be terminal 2 on the start relay. The capacitor will then connect to the same terminal and the other lead will connect to the terminal on the other side. Read More...