Karen H February 01, 2014 for Model Number MAH5500bww Which part do I need for my washer - the control panel keeps changing my settings and sometimes it will not work at all on any setting. Part number 22003238 or 22004436?
1 Answer Hello Karen. Based on the information you provided, it sounds like the console 22003238 is bad and will need to be replaced on the unit. Read More...
Bj S August 30, 2013 for Model Number MAH5500BWW I'm having problems with washer not operating. Lights on console and control board comes on but will not set to desire washing. I don't know if console is bad or control board is bad.
1 Answer BJ, With the issue that you are having of the unit not accepting commands would be caused by a faulty console assembly 22003238. Read More...
Cindy August 16, 2013 for Model Number Mah5500bww Maytag neptune front end load washer MY machine will wash and not spin out. Will pump out water but not spin off the excess water from clothes.. Do I need to replace the circut board for this unit? Serial # on this machine is 7493-2615zz and is about 13 years old. Thanks for your help... Cindy
1 Answer Hello Cindy. You will need to check all the balance switches and make sure the door is locking properly. Either will cause the issue you are having with the unit. Read More...
David April 16, 2013 for Model Number MAH5500BWW Having problems with the start button on the front panel controls. All other buttons work fine. Must push start many times before the machine will operate. Do I need to replace the entire control console.
1 Answer David, Yes the LED console would need to be replaced as a whole and you cannot just replace the start switch. Read More...
Sluggo February 08, 2013 for Model Number MAH5500BWQ also, is there schematic available of the main control board? I've got the wire diagram that shows the relay controls etc, but it is not detailed enough to tell for sure if my main board or my keypad is causing the overtemp. Thanks!!
1 Answer Sluggo, The manufacturer does not supply control board "blue prints" to distributors or servicers. The control board [ ] can get warm, due to the transformer mounted in it, but this doesn't "usually" cause an "overtemp" situation. Due to age and usage, you most likely have a few keypads that have failed, and will need to replace the control console/keypad assembly. Depending on the serial number, you may need : 22003239 for series 10 thru 84. or 22004437 for series 84 and after(the series number is the first two numbers or letters of the serial number). Read More...
Sluggo February 08, 2013 for Model Number MAH5500BWQ The flat membrane cable that connects to my touchpad control to the main control board shows signs of overheating. The system does not respond to some buttons. I believe I need a new control panel. The question is, which one. The serial number of the washer is 73793456ZQ. Which control panel do I need? There seem to be a bunch of different ones. I don't care about the color, by the way. Just function. Thanks!!!
1 Answer Hello Sluggo. Based on the information you provided, 22003239 is the control panel for the unit. Read More...
Phil January 03, 2013 for Model Number MAH 5500BWW Machine runs fine , replaced motor & control board 1 year ago . Will work on quick and normal wash. Cannot put into presoak or heavy soil modes. Light on cosole will not light up or activate in these modes .
1 Answer Hello Phil, The first thing that you always want to check is the wiring to ensure that there are no broken or loose connections. If this all checks ok then the console 22003238 would be what you would want to replace. This would be a failed Keypad. Read More...
Belinda September 01, 2012 for Model Number MAH5500BWW The panel will not light up when you open door and it will not turn on at all. Its getting power . Is it possible we fried the computer board during Issac?
1 Answer Hello Belinda. If there is power coming to the LED console and it does not work, you will need to order and replace the console 22003238 on the unit. Read More...
Kim July 29, 2012 for Model Number mah5500bww top lights up all buttons worked but beeps and wont let u use it cant change anything and chant get it to go into service mode do i need a whole new top with control board or just a new control board?
1 Answer Kim, You're on track, you most likely will need the console/keypad assembly 22003238 You will need the series(first two numbers of the serial number) to order the correct part. You could also remove the control console and test each button for a "closed" circuit when pressed with a multi meter, using the tech data sheet in the console. (unplug the power cord, remove the three screws across th top back of the console, push back on the bottom portion of the console and pull the top of the console towards you, and roll the assembly towards you). Read More...
Js January 22, 2012 for Model Number mah5500b Some of the lights are not lighting up when in use. Will this led panel fix the lights? Thank you
1 Answer Hello JS. Yes, if the lights on the control panel are not working properly, you will need to replace the led console 22003238. Hope this helps. Read More...