Lori November 06, 2011 for Model Number jdb1090 jenn air i a was useing the heated/dry button. the heated/dry won"t shut off. had to disconnect it. What part do i need?
1 Answer Lori, Are you sure the heater element is staying on and producing heat ? It could be you have a "stuck" keypad, and the light is staying on 6-919765 . Otherwise, The control board, would be the most logical, next step ( stuck heater relay on the board). Thanks and Good Luck Read More...
Christine September 10, 2011 for Model Number MDB8951AWS The display on top of the door doesn't work and a repairman who came out said that the display as well as the board which he opened and it showed some black inside should be replaced. Please advise on what parts to order. Thank you.
1 Answer Hi Christine. There are 3- different control boards that depends on your serial number to get the right one for the unit. Has it burned open? Please send us the serial number so we can assist you further. Thank you. Read More...
Andrew September 04, 2011 for Model Number MDB7601AWW Our D/W is less than 5 years old and the front digital display used to work, now intermittent to none, none of lights work on top of door, d/w will start but goes for 20 minutes or so, on its way here it used to be intermittent but still display 2hr, then it when to 20, then portions of 20 display missing, then blank, is it worth to repair suspected control board kit AP4009231, is it easy to do myself, or just move on.
1 Answer Andrew, You will most likely need the control panel/keypad assembly 6-919825. If you have a multimeter, you can check the keypad resistance using the "Tech Data Sheet " attached to the backside of the lower kickplate panel. It's a relatively easy repair, for someone with basic skills. If you're satisfied with the product, a repair is always less expensive than a replacement, especially if you do the repair yourself. Thanks and Good Luck Read More...
George K. May 20, 2011 for Model Number mdb8751awb 2hr. light blinks but when start button is pressed it won't start.
1 Answer Hello George. To cancel a Delay: When the delay is counting down, press the Delay pad again. The indicator light will go out and the cycle will start or resume immediately. To cancel a Delay and the cycle: Press START/Cancel once to drain and turn off thedishwasher. Or Press START/Cancel twice to turn dishwasher off without draining. If this does not help, try flipping the breaker switch off for 30 minutes. If the light is still blinking, then you could have a issue with the board 12002710 or the touch pad 6-919829, thanks. Read More...
James May 02, 2011 for Model Number MDB9750AWB Timer display blinks Won't run Top right wiring harness plug in at control board burnt - actully black and melted portion of plastic plug at board. 2007 - Board and Touch panel replaced.
1 Answer Hello James. You will need to replace the wire harness W10237912 and the control board to fix the problem your having. We will need your model number to determine which board you will need. Hope this helps. Read More...
Mike April 01, 2011 for Model Number MDB9600AWS We have not had ANY of the top buttons and light working for a while and when I had the repairman out to work on our clothes washer, I asked about the dishwasher. HE suggested replacing both electronic parts, since he's found either one could be the problem. I didn't write them down. I see you have both a control board and a control board KIT. I'm guessing THOSE are the same. Did he mean to include the Control Panel ? Which items would you suggest I replace? thanks Mike
1 Answer Mike, Here are the part numbers he referred to : 12002710 and 6-917720 . I would reccomend you remove the lower kickplate panel, and run the tests listed on the Tech Data Manual located in the plastic envelope taped to the back of the panel. Another method, order both parts, install the control panel first, if you still have a program problem, install the control board, Good Luck. Read More...