Bob February 09, 2013 for Model Number maytag mdb7650awb Lights on display don't work. Front time display went first, followed a week or 2 later by the rest of the lights. Only the "clean" light will light up when finished. Dishwasher runs normally. What should I check or replace? Dishwasher is a 2004 model. thanks.
1 Answer Bob, You want to start by checking or replacing the control panel/key pad assembly 6-919005. The LED lights and display are a component of the panel. The tech data sheet, should be attached to the back side of the kick plate, you can use the tech sheet and a multi meter to test each button on the keypad, if you wish. Read More...
John T December 06, 2012 for Model Number MDB9750AWS I have dishwasher maytag model mdb9750aws can not unclock control. I need control panel or control board?
1 Answer Hello John. If the button is not working on the control panel, you will need to order and replace the control panel on the unit. If the button is good, and the unit will not unlock, you will need to order and replace the control board. If you press the button and light goes off and on as a selection, then the button is good and the board is bad. Read More...
Jared August 10, 2012 for Model Number jdb2100aws My dishwasher will not stop. Once it completes a wash cycle it starts a new one. I also cannot change the cycle type or toggle any of the settings. Is this a 'control board' problem or even a 'control panel' problem? Thanks! jared
1 Answer Jared, You want to start at the control panel/keypad assembly 6-919766 . We'll send you some information, so you can conduct the control panel tests and circuit check the keypad ribbons so you can verify the situation. Thanks Read More...
Rick August 03, 2012 for Model Number Jenn-Air JDB1090AWS DISHWASHER I have a Jenn-Air JDB1090AWS Dishwasher. Whenever the power goes out, all the lights on the panel work except for the far right ones... start and delay. Usually after a day it works again. This time it hasn't started to work and its been three days. Any idea what needs to be fixed and what parts I need to do the job? Thanks for the help
1 Answer Hello Rick. Based on the information you provided, it sounds like the control panel 6-919765 is bad and will need to be replaced on the unit. Read More...
John May 05, 2012 for Model Number MDB7601AWW Maytag dishwasher, latch broke first and replaced. Now none of the lights or display are working. The washer still works fine. I'm looking at order a new control board for it. Part number 12002710. Is that going to fix my problem?
1 Answer Hi John. It will be advantageous to find the supplied tech sheet inside the cabinet to aid you in the diagnosis. It allows you to put the unit in a diagnostic mode which brings up fault codes and tells you which circuit needs assistance. Use a volt/ohm meter part #@ MA-DM1 to assist you in your diagnostics. Look at the control panel ribbon cable part # 6-919825 and make sure it is not kinked at the folds and flows smoothly. Use a pencil eraser to clean the connection and reinsert it into the board. If this does not relight the board then you need to go deeper in diagnostics mode. The service tech sheet will give the ohm's values as you check the control panel ribbon cable connections while pushing the commands individually. Then look at the inside of the control panel in the center where the power latch/switch assy pivots on the back side. If the V-tabs have broke then you need to replace the control board itself. Then insure the unit is properly leveled with all 4-legs touching the ground. The field service test will help from here. Be sure to let us know how we can help further . Thank You. Read More...
Frank April 14, 2012 for Model Number JBD1100AWS I have a problem with my 5 years old dishwasher. Last year I replaced my membrane touch pad since some buttone did not work. Now my problem is that the liquid dispenser/gel pacs are being released late. After the cycle is complete, the gel pac is sitting at the bottom of the dishwasher unused. Is this a microprocessor probem? If so, what part do I need? Thanks
1 Answer Hello Frank. Check and make sure the dishwasher is filling with water. If so, make sure the dispen is clean and does not have alot of soap scum on it. If it is clean, you will need to replace the control board 12002710. Hope this helps. Read More...
Rick April 04, 2012 for Model Number maytag MDB8951AWS I have been having problems with the touch control pad. First the start button would not work but then I would turn off the breaker and a little later it would work. It worked for about a month, now I can see a few dim green lights on some of the settings but not all of them, and start does not work at all. I know you have a touch pad and a control panel replacement part I want to make sure I buy the part it needs. Please help.
1 Answer Rick, The most likely and common fault for your description is a control panel / keypad circuit failure 6-919831. If you have access to a multimeter, you can tets each keypad circuit for proper resistance using the tech data / wiring diagram located on the back side of the kick plate panel, in a plastic bag, if it hasn't been removed or lost. Good Luck and Thanks Read More...
William January 11, 2012 for Model Number JDB1250AWS I got AP4009231 as not all the lights were lighting on the control board when pressed. After installation of the new board different lights would light up, but still not all would light when pressed. The dw seems to cycle through the appropriate cycles, but I'm not sure. On either board do the normal heavy wash light come on when pressed, but the Dishes come out clean. Is it the "other circuit board" as listed as 12a or the touch panel, or is the circuit board defective? thanks.
1 Answer Hello William. If the buttons are not working properly, you will need to replace the control panel 6-919765 on the unit. Hope this helps. Read More...
Steve December 09, 2011 for Model Number JDB1100AWS The lights and buttons on the top of the unit stopped working and the lights went out. I put a new circuit board and a new control panel on, but nothing is working still. Any other steps I have missed? We checked to make sure power was being provided to the unit and there is power going to the board.
1 Answer HI Steve. First look at the unit and make sure it is level front to back and side to side. This will properly line the door switches/latch assy. If the unit (back legs especially) are not level and solid the unit door will flex and not close the switch feeding the control board. See if you are getting 120 vac to the control board when the latch is tripped closed. You can unbolt the door striker and use it momentarily for this test. If you are getting 120 vac to the board, then you can use the tech sheet behind the kick plate to put the unit in a self diagnostic field test. It will allow the fault codes to point in the circuit of failure. Thank You. Read More...
Steve December 09, 2011 for Model Number JDB1100AWS The lights and buttons on the top of the unit stopped working and the lights went out. I put a new circuit board and a new control panel on, but nothing is working still. Any other steps I have missed? We checked to make sure power was being provided to the unit and there is power going to the board.
1 Answer HI Steve. First look at the unit and make sure it is level front to back and side to side. This will properly line the door switches/latch assy. If the unit (back legs especially) are not level and solid the unit door will flex and not close the switch feeding the control board. See if you are getting 120 vac to the control board when the latch is tripped closed. You can unbolt the door striker and use it momentarily for this test. If you are getting 120 vac to the board, then you can use the tech sheet behind the kick plate to put the unit in a self diagnostic field test. It will allow the fault codes to point in the circuit of failure. Thank You. Read More...