Steve March 16, 2024 for Model Number MDB9979skz We had a power surge in the area, now the dishwasher is dead. The buttons all on top of the door are not working., there is power to the unit. So is there testing or a fuse on this model? Thanks Steve
1 Answer Steve, there is a fuse in the wiring harness W11662347 and it can be identified if it has failed by testing for 120VAC at the main control W11410063. If there is voltage present at the junction box but not at the control, the wire harness would need to be replaced. If there is voltage at the main control, it is likely that the main control has failed. Read More...
William November 23, 2020 for Model Number KUDC101XBL1 I have a Kitchenaid d/washer & I have to keep resetting the breaker in order to get it to run. When it runs, it works fine,, however @ the end of the run cycle & after drying, a couple of the blue lights stay on, & I can't start it up, without "rebooting" the machine. Suggestions?
1 Answer Hello William,the switch membrane/console is starting to fail, it is part WPW10481129. Read More...
William April 29, 2020 for Model Number MDB8751AWS I had a broken handle so I replaced with a new switch and latch assembly. I turned it on and it ran fine for a week. Now it will not start. I checked the latch switches and they are working fine with a OHM meter. All the lights work on the cycles and when I set it for wash and close door land press start button, it will not start and flashes 2H and I can not change delay or get anything to happen then after a few min the lights all go off.
1 Answer William, with the power supply turned off to the dishwasher, it would be recommended that the keypad on the control panel 6-919829 is tested to identify if the keys are working properly. If the keys test good, then the likely failure would be in the main control 12002710. Read More...
Lloyd April 09, 2020 for Model Number JDB1100AWS My dishwasher is not starting. Only one LED light is illuminating (this has been the case for a while). I tried cutting the power source and then turning it back on. Is it the control board or control panel/touchpad that needs to be replaced?
1 Answer Hello Lloyd, You should first run a field service test. A Field Service Test may be started by pressing the Heated Dry key 6 times followed by the Start key within 8 seconds. This test must be performed with clean water to ensure proper sensor performance. “88” will appear in the display (if available*) and the following sequence of events will occur:SECONDS FUNCTIONS / ACTIVE LOADS106 Vent Wax Motor / Water Valve5 Thermistor check / Turbidity Sensor check & calibration - no loads active.120 Wash Motor / Vent Wax Motor / Dispenser Wax Motor180 Wash Motor / Heater / Vent Wax Motor120 Drain Pump4 Water ValveThe time for the Thermistor check / Turbidy Sensor check & calibration may vary slightly. The Field Service Test will not repeat. The Heavy Wash LED will Flash during the test mode. All Indicator lights (except Heavy Wash) will illuminate. If thedishwasher door is opened during the test, the test sequence will pause, and resume when the door is closed. To cancel the test, press the Start/Cancelkeypad. The control has been designed to test the Sensor, Memory, and Motor. During the Field Service Test, if a fault has been detected, the test will abort any time after the motor current has been checked and 2 or more LEDs will begin to Flash. A Memory / Software Check will occur immediately after the test is started. The (Delay / Delay 2 hr) LED and one of the following:Turbidity Sensor - failure - Hi-Temp Wash LED/Extra Rinse LEDThermistor - failure - Heavy Wash LEDMotor - high current - Normal Wash LEDMotor - low current - Light Wash LEDMemory Failure - Heated Dry LED Read More...
Bob March 17, 2020 for Model Number JDB1250AWP Led lights, not screen located on top inside of the unit is not working. How do we tell if the strip is bad? Is there a part number for the strip?
1 Answer Bob, This issue would most likely be caused by a faulty control panel if the lights are not working. The part number for the control panel would be 6-919765 but the manufacturer has discontinued this part with no suitable replacement available. Read More...
James December 24, 2019 for Model Number WED8300SW0 With this model Whirlpool Duet Dryer what is the P/N for the front control panel board? I need to replace the unit because of a power surge that destroyed my power outlet. When I replaced the power outlet and had power to the machine the control board lit up but I was restricted to a low heat setting. What can I do to restore the control board to allow different settings as in the past?
1 Answer James this would be the control panel part number WP8571955 that would be needed. Read More...
Bernie December 16, 2019 for Model Number CWG3100AAB i saw two control boards on your site both looked identical but different numbers
1 Answer Hello Bernie,the correct control board for your model is 12001620 however it is no longer available as it has been discontinued by the manufacturer. Read More...
Argusweb September 12, 2019 for Model Number MDB8751AWW Model # MDB8751AWW Serial # 30127461JC Your site shows two options for the control board I need to replace on my dishwasher: Part # AP4009231 & Part # AP6017275 One is priced at $114.12 and the other at $132.91 Both say they are Original Equipment and compatible with my model number. Based on my Serial Number, does it matter which control panel I use? They appear in the photos to be the same part.
1 Answer ARGUSWEB, Yes, though the boards "look" the same, but the circuitry has been relocated and/or revised and routed differently. Yes, the serial number will designate which control board is the proper board for your dishwasher. Read More...
Carl June 25, 2019 for Model Number DU1055XTVS8 The dishwasher will not start. The normal light is blinking all the time and the cancel light sometimes starts to blink also. Tried disconnecting the power with no luck. How to narrow the problem down?
1 Answer Carl, with the power disconnected to the dishwasher, you will want to test the keypad as this issue will indicate a shorted key being sensed by the main control. To test for a shorted key, the keypad ribbon would need to be disconnected and tested from pin 13 to pin 4 for continuity. If there is continuity without the keypad being pressed, then the normal keypad is stuck and would need to be replaced. If there is not continuity, then you will want to continue testing by pressing the normal key on the same pins. If there is not continuity with the key pressed, then the keypad has failed. If the continuity check passes, then the main control [WPW10285180] would be the issue. If the keypad fails, then the part number is WPW10459141 for bisque, WPW10459140 for white, and WPW10459139 for black. Read More...
Dan January 21, 2018 for Model Number JDB1270AWY The heating element on my JDB1270AWY dishwasher does not turn off. As soon as the unit has power, the heating unit is activated and will stay on continually. Since the heating element is working, is this likely a control board failure, or something else? What's the best way to diagnose the failed part?
1 Answer Hello Dan, you can test the red/black wire on the heater for voltage to ground. If power is present as soon as you connect the unit back to power, then you will need to replace the board 12002710. Thanks! Read More...