1 Answer Hello Billy. You will need to replace the transformer in the unit. I could not find your model, but for model number MIM1554XRS0, it uses part number WP2310139. Read More...
Jim October 17, 2013 "I have a Kitchenaid cabinet icemaker Mod KUIS18NNTS1It quit making ice suddenly. The recirculating pump is not working. There is 12 vac at the pin connector of the pump when it should be recirculating. That voltage goes away when I plug in the pump. Everything else works,The water reservoir fills, the evaporator gets cold, and heats on the harvest cycle. I've replaced the pump and the control board.
1 Answer Hello Jim. Check and see if the water level sensor WPW10548509 is bad or the wiring harness is bad on the unit. Read More...
Jim B October 10, 2013 I have a Kitchenaid cabinet icemaker Mod KUIS18NNTS1. It quit making ice suddenly. The recirculating pump is not working. And there is only about 2 vac at the pin connector of the pump when it should be recirculating. Everything else works,The water reservoir fills, the evaporator gets cold, and heats on the harvest cycle. Am I looking at a new control board? or is there something else that could be causing the pump not to com on. Jim
Michael K July 27, 2013 for Model Number 2255433 When I ran diagnostics on my ice maker the optic control board was working fine and the ice maker needed to be replaced. I installed the new ice maker per instructions after I got it from appliance parts pros, and now the optic control board all the sudden shows deffective. Did I do something wrong? It was working ok before I replaced the ice maker.
1 Answer Hello Michael. It could have tested good, but actually have been starting to fail. If it test bad, you need to replace the emmiter boards on the unit. Read More...
Scott M. May 20, 2013 for Model Number Kitchenaid KUIS15NRTS My ice maker makes sheets of ice but the cutting grid doesn't get hot enough to cut the ice. I removed the cutting grid, cleaned it of any residue and also ran cleaner through the cycle but it still doesn't cut the ice. Any suggestions of what could be the issue would be appreciated. Thanks, Scott M.
1 Answer Hello Scott. If the heater is good, the it sounds like the transformer WP2310139 is bad and will need to be replaced on the unit. Read More...
Scott S January 07, 2013 for Model Number whirlpool GD5RVAXVY01 Ice maker stopped making ice all of a sudden after working fine for 4 years. I replaced ice maker assembly module and still no ice. No water filling ice tray and no movement of ice tray assembly. The ice maker control knob on right side of freezer is on and red light is blinking. Water flows well through water dispenser. How do I know if ice maker control is working? Should the red light be blinking? It still blinks when I turn to off position. It blinks twice, then pauses and then blinks twice again when in on position.I have control panel on fast ice and fast cool. I live in Florida and there has been high humidity lately and water condensing on doors. Thanks, Scott.
1 Answer Hello Scott, When you shut the icemaker control off and it continues to blink this means that the emitter board W11629974 is defective and needs to be replaced. You would also want to check door seals if you are getting a lot of condensation on the doors. Read More...
Bobby A November 15, 2012 for Model Number KUIS18NNTB1 This unit has an auxillary drain pump. When the unit is turned on, the water valve opens and over fills the water pan, then the water shuts off, the recirc pump starts and pumps for one minute then shuts off. The pan drain pump starts and pumps the water out in to the auxillary pump. The water valve opens and starts the process all over again. It just keeps going through the same process. I have also noticed when the auxillary drain pump starts, the interior light and the on/off light goes off for a second. Sometimes the auxillary pump never shuts off. I have replaced the water level sensor, bin and evaporator thermistor. Now I am beginning to think it is the control board.
1 Answer Hello Bobby, Based on the information provided it appears that your auxilliary pump 1901A is bad and needs to be replaced. The unit power is routed through the pump and into the unit. The pump is causing surging and the unit to restart. Read More...
Derek S November 15, 2012 for Model Number KitchenAid KUIA15NLHS11 We just got this Ice Maker from a friend, but it does not seem to want to stop making ice. The unit will turn on, It will make ice, but it just keeps making ice. None of the buttons on the control panel work either. Any suggestions?
1 Answer Hello Derek. Based on the information you provided, you will need to replace the switch WP2304122 and the bin control WPW10503764. Read More...
Dennis June 20, 2012 for Model Number KUIC15PRTS0 im rebuilding this ice maker , when i got it the control board was missing , so i got a new one and installed it , my question is ...are all the plug in sockets used on this board , i have one left over with nothing in it ...it is the small white one right next to where the control panel strip plugs in. what does that junction control? note , this unit does not have the secondary drain pump located next to the compressor it just free flows down into a drain in the floor ALSO the service buttons and reset buttons appear to do nothing note this machine does not have the
1 Answer Dennis, WPW10141364 is the correct part for the model number you supplied. It has been "substituted a few times and may have an additional connector that you won't use. We're sending you some service information that should help you determine what connections attach to which connector. Thanks Read More...
Mark 2 June 07, 2012 for Model Number GI15NDXTS2 The condensor is clean of all dust - any other suggestions you can offer?
1 Answer Hello Mark. No, if the condenser is clean, it just sounds like the motor W10124096 went bad on the unit. Read More...