Jim C August 03, 2013 for Model Number MDBH955AWW Replacing control panel, how do you release the ribbon to circuit board?
1 Answer Hello Jim. Press in on the locking tabs on the connector and lift of the locking tab. Then pull the ribbon cable from the connector. When you install the new ribbon cable, make sure you press the tabs down to lock the ribbon cable into place on the unit. Read More...
Marty July 27, 2013 for Model Number MDBH955AWS We went to use the dishwasher and hit the start button. Nothing happened. We are thinking of ordering a new control panel as it does not light up. Is that the correct place to start for replacing parts. We replaced the handle and switch two years ago and I don't think it is that again.
1 Answer Hello Marty. If there is power to the unit and it does not work, replace the control panel on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Greg June 30, 2013 for Model Number MDBH955AWW Maytag dishwasher abruptly failed to start. The only button that lights up on control panel now is the child lock/unlock button. Nothing else works. Power to unit is good. Cycled power off and on several times. Door latch switches have continuity. When I checked for proper connection of ribbon cable, noted what appeared as corrosion on a couple of the traces. Assume I need a new panel, but what would cause the cable to go bad? Unit is only 3 years old.
1 Answer Greg, You're correct, the issue is most likely the key pad ribbon is damaged due to the corrosion. When you dismantle the door liner and control panel, Look at the inside of the components for signs of condensation, moisture, or leakage. Whenever the dishwasher door is closed and latched, there is voltage supplied to the control board. The key pads have a low resistance / voltage circuit as well. this is usually where the corrosion is produced. You may want to try this, when you remove the keypad ribbon from the control board connector check and make sure there's no corrosion on the connector pins(use electrical contact cleaner) when you insert the ribbon into the connector and made sure the ribbon is tightly and properly installed, apply a thin coat of "Vaseline" all around the connector and ribbon, this will help to reduce the corrosion that can develop on the ribbon and connector. Read More...
David May 30, 2013 for Model Number mdbh955aww dishwasher control panel lamp goes to rinse only sometimes you can get it to light on one of the other options but it goes back to rinse only. i have cut power to dishwasher trying to reset it but that doesn't work
1 Answer David, The control panel/keypad assembly 6-920244 is the place to start, based on your post, it's the more likely issue. Read More...
William S May 24, 2013 maytag mdbtt60aww won't start. cycle lights go on when pressed but press start and nothing happens. Sheet says pin 10 to pin 6 should show open circuit and when pressed read 10 ohms. How do I identify pin numbers?
1 Answer William, In most cases, pin #1 is usually marked on the control board connector with an arrow or the number 1 as well as the ribbon tracer. You may have to look very closely, they can be hard to see at times. Read More...
Anil March 24, 2013 for Model Number Mdbh945AWB3 Few weeks all indicator lights on front panel acting weirded now there is all cycles you can go and pick but start button do nothing, it will not start. Once in while it worked. Now all front panel lights are very dim. You can hardly see anything on it. What should I change? Is panel includes control board too ?
1 Answer Anil, You will want to check the connection at the control board for the ribbon cable. If this checks ok then the most likely cause is a bad membrane switch/control panel 6-920244. Read More...
Al February 23, 2013 for Model Number MDBH955AWB Last week tried to use my dishwasher, first of all the lights were acting crazy, then it started the cycle, when it finished, the water did not drain. after cleaning the mess, i tried to run a quick rinse, but it did not work as well. once again the dishwasher didn't drain. what could the the issue?
1 Answer Al, First check and make sure the power supply connections in the junction box on the front frame of the dishwasher are good and tight. Then test or replace the control panel/keypad assembly 6-920244. The LED lights and keypad circuits are imbedded in the control panel, ir there is an issue with a pad circuit, it could cause the machine to stop in midcycle, etc. Read More...
Kirk W January 30, 2013 for Model Number mdbh955awb Hello, I have a maytag quiet series 300, Legacy series. My problem is that I can chose any wash cycle and it will begin to fill with water like normal, but after it fills and the motor kicks in it will only run (the motor) for 3 seconds and then quits, this repeats 4 or 5 times and then the whole unit shuts off.
1 Answer Hello Kirk, You will want to check the pump to see if there is something that is clogged in it. Unit having something jammed can cause unit to kick out on overload. You will also want to check the amp draw of motor when it turns on. The Amp draw should be approximately 3.2 plus or minus 10 percent. If over this then you have a bad motor. You can also check the resistance of the motor windings. The motor winding resistance should be 3 to 4 ohms. Read More...
Carolyn B. January 26, 2013 for Model Number mdbh955aww The dishwasher works fine but the lights on the control panel no longer light up. What part is needed? How difficulot is it to install?
1 Answer Carolyn, The "LED" lights and the display and keypads, are a component of the control panel 6-920244 It's not a dfficult repair to perform. You will need "torx" tips and a driver. " 1. Disconnect power to the machine. 2. Open the Dishwasher door. 3. Remove the 11 Torx™ screws along the sides and top of the Inner Door Panel. 4. Separate the Inner Door Panel from the Outer Door. 5. Disconnect wires from the Dispenser Wax Motors before pulling the Inner Door Panel away from the Dishwasher. Remove PC Board Housing Cover. Disconnect Membrane Switch from PC Board. Remove PC Board Base. 6. Lift out Latch Assembly. Remove 4 screws securing Control Panel to Outer Door. NOTE: Facia is susceptible to damage during reinstallation." Read More...
Mike August 14, 2012 for Model Number mdbh955aws Rinse only function no longer works, also door handle broken will replacing the control panel (ap4365164) fix these problems.
1 Answer Hello Mike. The control panel 6-920244 will fix one of the issues, but will not fix the handle. You will need to order the latch assembly W10862259 also. Read More...