Tj April 13, 2011 for Model Number KUDM01TJWH0 I replaced the Electronic control assembly about a month ago because I found where the com 2 connector plugs into the board was showing that it was burnt up on both sides. The original problem was that the dishwasher would try to work for a couple seconds then quit with the lights working and then it would shut off, now the only bottom that lights is the cancel button. Unless I unplug the ribbon, then and it will light for 20 seconds and then quit again. Please advise?
1 Answer TJ, have you cleaned the insertion end of the ribbon with alcohol ? You may want to try that first, and reset the control board "HI TEMP SCRUB, AIR DRY, HI TEMP SCRUB, AIR DRY Or SANI RINSE, AIR DRY, SANI RINSE, AIR DRY (Note: HI TEMP SCRUB = HI TEMP SCOUR) (Note: AIR DRY = NO HEAT DRY = ENERGY SAVER DRY If the above key sequence is entered with the dishwasher in Standby, the Diagnostics Cycle is started. The Diagnostics Cycle can be rapid-advanced, interval by interval, by pressing the Pots&Pans/Heavy or Anti-Bacteria/Cookware or Start key. If your problem remains you should replace the control panel assembly WP8270226 next. Good Luck Read More...
Lucy April 11, 2011 for Model Number KUDI01TJBL0 I Replaced control board #8564542 all control lights work nothing happens when start button is pressed. The cancel/drain light works and will drain when pressed but does not cut off.
1 Answer Lucy, try this "HI TEMP SCRUB, AIR DRY, HI TEMP SCRUB, AIR DRY OR SANI RINSE, AIR DRY, SANI RINSE, AIR DRY (Note: HI TEMP SCRUB = HI TEMP SCOUR) (Note: AIR DRY = NO HEAT DRY = ENERGY SAVER DRY). If the above key sequence is entered with the dishwasher in Standby, the Diagnostics Cycle is started. The Diagnostics Cycle can be rapid-advanced, interval by interval, by pressing the Pots&Pans/Heavy or Anti-Bacteria/Cookware or Start key. Let the control run the complete diagnostic/test cycle, then attempt to start the unit again. If problem persists, re check the connections on the control board and repalce the touchpad assemblyWP8270223. Good Luck Read More...
Mr, B April 06, 2011 for Model Number Kudso1flwh6 All lights on control panel light up when pressed to select desired schedule. Problem is when the start button is pressed nothing happens. No sounds or anything. The unit then shuts off the selected lights. Problem appears to be in the start of control. Does the control panel include switch located under the buttons? If I order the control panel is all the necessary parts included?
1 Answer Hello Mr. B. The control assembly is just the control board. Here is the part number for the user interface WP8270168 with the buttons. It would be wise to replace the ribbon cable WP8524447 as well. Hope this helps. Read More...
Rmattei April 02, 2011 for Model Number GU1500XTLQ3 Running in normal cycle, the panel shows 52 (min) and stays all the time and does not move to another step.In china crystals it happens at 42 (min).
1 Answer Hello RMattei. It sounds like you may have a bad electronic control. Part number WP8564543 is the correct control for your model. Hope this helps. Read More...
Marty R. April 02, 2011 for Model Number KUDI01TJBL0 Hi Guys, I did hold the Control Lock, Energy Saver Dry button for 4 seconds and it blinks 3 times but never turns off.
1 Answer Hello Marty. If you are pressing and holding the Energy Saver Button for 4 seconds and the light is not turning off then you will need a new board. Your part number is WP8564543. Thanks! Read More...
Marty R. April 02, 2011 for Model Number KUDI01TJBL0 I can't turn off the Cntrol Panel Lock. When I press it it blinks 3 times, and stays on. What can I do to turn it off?
1 Answer Hello Marty! To turn the control lock off press and hold ENERGY SAVER DRY for 4 seconds. Hope this helps! Read More...
Jt March 25, 2011 for Model Number 665.17342300 I hooked up wires to soap dispenser. The acuator comes on ,flips door open and stays on. It buzzes continously as if a switch is frozen in a ON position. Is this the board. Thanks.
Mike March 21, 2011 for Model Number KUDI01ILBL1 The control light is the only light that is burning. No matter which button I press, the CL blinks 3 times. Even if I press CANCEL. Is this telling me anything? Thanks.
1 Answer Hello Mike. Check and see if the panel is locked. If so, press and hold the Air Dry key for 5 seconds to turn off (or on) the Control Lock feature. Hope this helps. Read More...
Jt March 15, 2011 for Model Number 665.17342300 My soap depenser does not work properly. I was told it may be the board. I replaced mag buzzer. It buzzes to open and continues. Is it the board. Sears told me either or. Help.
Bill March 11, 2011 for Model Number kudr0itjbl0 The board on my unit burned up. I ordered a new board #ap3775964 this board does not match the plugs on my unit. Also the control panel and ribbon is burned up and I can't tell from your break down which one I need.
1 Answer Hello Bill! For the black control panel order WP8270229. This includes the ribbon. The control board ordered WP8564543 is a replacement board and matches your model number. I have located a link on our repair forum that may help with the install process, hope it helps! http://forum.appliancepartspros.com/dishwasher-repair/178582-control-board-connectors.html Read More...