Rich F. May 10, 2011 for Model Number 665.15932000 The only lights that come on are the hi temp scrub, sani rince and air dry. Otherwise nothing works and the machine will not start. This happened after and electrical storm.
1 Answer Hello Rich. Remove the ribbon cable from the control board and make sure it is clean and dry. If the problem presist after cleaning the ribbon cable, you will need to replace the control panel. We will need the color of your unit to supply the correct part number. Hope this helps. Read More...
Peter May 05, 2011 for Model Number KUDS01DLSS2 The dishwasher is emitting a constant pump like sound that never stops unless I open the door. Other than that everything functions properly. Even if I hit the reset it will continue. I have run diagnostics and no warnings come back. I have checked the pump drain, screen and impeller and there are no obstructions. The heater element is also working fine. I suspect the fix is a new electronic control. The only other possibility might be a deffective control panel, although this is doubtful as I have unhooked the ribbon connection and still get the sound. Any suggestions appreciated.
1 Answer Hello Peter. You will need to test and see if the relay in the board is stuck and sending power to the pump. If so, you will need to replace the control board WP8564543. You can test this with a multi-meter MA-DM1. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Brambo. May 01, 2011 for Model Number GU1500XTLS1 My dishwasher started getting stuck in the 2 min drain cycle at the start of every cycle. Then I would hit the cancel button and it would work fine. Then I went to start a new cycle two weeks later and the PANEL LOCK light is stuck on. The light will not shut off. I've tried holding the air dry button down and cutting the power to the unit. It stays locked. All the buttons work on the front and are not stuck in position. What part should I replace? The electronic control assembly or the Panel? Thanks for your time.
1 Answer Hello Brambo. If the unit was going straight to the drain function, it sounds like the board is bad. However, you can test the control panel. When you press a button, you should see continuity on the pins listed for that button. If it does not read correctly, you will need to replace the control panel WP8534840. You can test this with a multi-meter MA-DM1. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html CANCEL/DRAIN P1-12 P1-2 SOAK & SCOUR P1-11 P1-3 DELAY HOURS P1-12 P1-3 ANTI-BACTERIA/BAKED-ON COOKWARE P1-13 P1-3 HIGH TEMP SCOUR/HIGH TEMP SCRUB P1-11 P1-4 START P1-12 P1-4 POTS & PANS/HEAVY P1-13 P1-4 SANI RINSE P1-11 P1-5 RINSE ONLY/QUICK RINSE P1-12 P1-5 NORMAL WASH/NORMAL P1-13 P1-5 AIR DRY/ENERGY SAVER DRY/NO HEAT DRY P1-11 P1-6 QUICK WASH/QUICK CLEANUP/TIME SAVER P1-12 P1-6 CHINA/LIGHT P1-13 P1-6 Read More...
Vic April 28, 2011 for Model Number KUD101flbl0 When we put it to any cycle to wash or rinse it works fine except it will not drain on its own, if I hit the drain button it will work and drain, possible remidy??
1 Answer Hi Vic. Since you can manually activate the drain cycle it could very well be the control board WP8564543. The board is not sending power to the drain pump when it should during a cycle. Hope this helps! Read More...
Mike April 28, 2011 for Model Number kudp01flss6 Dishwasher stopped working,clean light flashing. Replaced control board same problem
1 Answer Hello Mike. You will need to put the dishwasher in stand by mode. Then press heated dry, normal, heated dry, normal, within 6 seconds. The unit should start a cycle. Let it run through the cycle and complete. You will need to test the heater WPW10082892 and the thermal cut-off WP661566. They should read closed for continuity. If they are good, you will need to get your water hot at the sink each time before you use the dishwasher. You can test this with a multi-meter MA-DM1. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Jody April 23, 2011 for Model Number kudso1ilbs6 The display shows 2 dashes and the "normal" and "rinse only" lights are blinking (no other lights illuminate). The reset code Hi Temp Scrub, Energy Saver Dry, Hi Temp Scrub, Energy Saver Dry does not turn on any other indicators. I have bypassed the door latch switch(jumper) and I have bypassed the fuse(jumper) to no avail. Also I have checked the ribbon connections and everything is clean and well connected. Do you think this is this the control board or the touch Panel? How do I know if the machine in "standby"? Thanks!!! JS
1 Answer Hello Jody. According to the manufacture, if the door latch is good and is powering pin number 8 on the board, then you will need to replace the touch pad control panel. Hope this helps. Read More...
Nic April 18, 2011 for Model Number KUDS01IJBS1 Our dishwasher, on the normal cycle, gets stuck for a good while on min 83 and later on min 42, it does complete but it takes a long time. Thanks, Nic
1 Answer Hello Nic. Check and make sure you are getting the water hot at the sink, before you start the dishwasher. If the water is hot, then test the thermostat WP661566 and make sure it is good. It should read closed for continuity. Hope this helps. Read More...
Brett April 17, 2011 for Model Number KUDM01TJBT0 Start button quit working. While troubleshooting also found that the "Rinse Only" and "Hi Temp Scrub" don't seem to be working either. Since Hi Temp does't work I don't think it will reset. Door lock seems to work because I can get the "Cancel/Drain" to start the pump to drain it. Seems to be the Interface, Ribbon Cable, or the Elect. Cont. Any suggestions?
1 Answer Hello Brett. If some of the buttons are non responsive, it sounds like the control panel WP8270226 is bad and will need to be replaced. Check and make sure the ribbon cable is seated good and is dry. Hope this helps. Read More...
John April 15, 2011 for Model Number GU1500XTKQ0 I checked the heating element (showed continuity:good)tested wires (no continuity), tested thermostat (showed continuity:good?) tested wires (no continuity). Suggestions next?
1 Answer Hello John. Try running the water at the sink and getting it hot before starting the dishwasher. If the problem continues, you may have a bad control board. Hope this helps. Read More...
John April 14, 2011 for Model Number gu1500xtkq0 I turn unit on normal cycle, runs for few minutes, stops; shows two dashes, soak and scour button blinks, after a minute or so it starts again, runs a short time, goes thru same thing as above 2 or three times and finally stops with 2 dashes showing and soak and scour button flashing.
1 Answer Hello John. You will need to check the thermostat WP661566 and heater W10518394 and make sure they are good. They should read closed for continuity. If they are bad, the unit will not advance. Hope this helps. Read More...