Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Refrigerator Defrost Timer by Whirlpool

Best Seller
Manufacturer Part
4.89 (64)
By: Whirlpool
Part Number: OEM18017991
Manufacturer Part Number: WP2183400

Freezer frosting up or refrigerator not cooling? The defrost timer controls the defrost cycle. DIY-friendly repair, typically 30 minutes to install.

More
$63.65

IN STOCK
Ships Today Guaranteed
Add to Cart

Questions & Answers

For Whirlpool Refrigerator Defrost Timer (Part Number: OEM18017991)

David for Model Number Estate TT14DKXEW14

Whirlpool 2183400 defrost timer Recently repaired my fridge by replacing timer, bimetal, & heater coil - ordered from you. Successful BUT don't understand something....... When bench testing the timers (old and new) - I applied 110vac to terminals #1 & #3. Advancing the timer by hand, #1 switched between #2 for defrost or #4 for cooling as expected. BUT, the timer would not advance on its own over a period of several hours (based on a pencil mark) when it was on the bench but advanced properly when installed in the fridge. I understand there is a capacitor in series with the motor but not sure what impact this would have. Can't sleep for wondering what is happening - thought I had a reasonable understanding of electricity. PLEASE explain why the timer did not advance when on the bench. Thanks

1 Answer

Hello David. The timer motor is power through the compressor run of the unit. Ont the bench, you were not supplying power to the timer motor. On the unit, there is power to the timer motor. Thus, the motor advances.

Read More...

1 Answer

Patrick,

Check the rear wall of the freezer and see if there is frost build up on the wall. If so, you will need to test the defrost heater and the defrost thermostat. They should read closed for continuity when cold. You can test this with a multi-meter TJMA-DMT3. I will include a link at the end to assist you how to use the multi-meter if needed. If both parts are good, you will need to replace the defrost timer. Once the problem is repaired, you will need to thaw out the ice on the coils before the unit will operate properly. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Read More...

1 Answer

Randy,

This timer should be a continuous run timer which means that it will run and advance all the time whether the compressor is on or off. If the timer is not advancing then the timer may be faulty.

Read More...

1 Answer

Hello KJ. Make sure the coils on the back are clean, and if it is cooling properly, but not turning off, replace the temperature control WPW10567140 in the unit.

Read More...

1 Answer

Hello Clark. The gears move so slow, you will not see them turning unless you mark a gear and watch the mark on the timer WP2183400.

Read More...

1 Answer

Hi John. A little conflicting info... If you say the heater works when the timer is manually advanced then there is an issue with either the timer itself or the wiring. Is the pink wire on # 2 timer connection ? Is the Blk on the # 1 ? Is the orange on the # 4 and the red on # 3 ? It also is marked on the side of the timer. Timer part # WP2183400. The heater should have 8-18 ohms resistance. It is part # WP2006751. The defrost thermostat is part # WP4387499. It seems like if the heater fully gets hot then you have a wire connection issue or a timer issue. Let us know what you find and we will continue to assist. Thank You.

Read More...

1 Answer

Hi Curt. You will need to replace the defrost thermostat and heater. Defrost heater - If you need the defrost thermostat order WP4387490
Part Number: WP2263749, made by WHIRLPOOL. Thank you.

Read More...

1 Answer

Hi Hailey. Your defrost timer is located in the top. You remove the front cover by lifting and setting aside. Then you will see the mount screws and the defrost timer knob on the left under the fan cover. You remove the cover and un- bolt the timer. Unhook the electrical connector and reinstall the defrost timer. Make sure that you advance the timer with a large straight blade screwdriver to the 2nd "heavy" click so the timer will start in run time. Hope this helps. Thank you.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google