1 Answer Al, Unfortunately we do not have a video on removing this part and would need the model number of the unit to be able to assist properly. The model listed does not come up valid. Read More...
Patrick December 19, 2015 We saw water on the floor when the dishwasher was filling and it appeared to be leaking at the drain pump
1 Answer Patrick, If the drain pump is leaking then you will want to replace the pump. We would need the model number to be able to assist with the part number for the pump. Read More...
Joseph November 30, 2015 for Model Number MDBTT50AWW I have a Maytag Quiet Series 200 Dishwasher (Model # MDBTT50AWW) that is having intermittent draining issues. Looking at the questions here and elsewhere online, I think it is the Drain Pump. When I look them up on here it gives me two different models. Part Number: AP4364233 Made by: Whirlpool Price: $54.66 Part Number: AP5272754 Made by: Whirlpool Price: $69.54 I am hoping someone can tell me what the difference is and if they are 100% interchangeable or if one is better and why? Your help is much appreciated.
1 Answer Hello Joseph. We will need your serial number to determine which pump you need to order. Read More...
Ski February 05, 2015 for Model Number maytag quiet series 300 My dishwasher would not drain - I took the bottom assembly apart and found a red rubber gasket blocking the drain. I removed it, not knowing at the time it was part of drain pump AP4364233 . Dishwasher is running now. will it work without this gasket - it is pretty beat up? thanks
1 Answer Ski, The dishwasher will work but you may have drainage issue and water coming back into the unit with the flapper off. You will want to replace this flapper. Read More...
Sk May 26, 2014 for Model Number MDB7600AWS My dish washer drain pump stopped working. I replaced with part # 6-917641. Once I connect the power, the drain pump started running. Initially I thought, there might be some water inside and it's attempting to drain. The drain pump sound is there always. When I start a cycle, I hear water gushing sound and motor starting sound. At the end of the cycle, there is no water inside. That means drain pump is working. However it's not stopping at the end of the cycle. I have to leave the door open or cut the power to turn off pump. So far I ran two( 2) complete cycles. Once without any dishes and next time with dishes. The dishes are not cleaned.What could be the problem? Are there any diagnostics, I can perform? Thanks in advance.
1 Answer SK, Yes there are diagnostic tests you can perform. You will need to remove the lower kickplate and access panel from the front of the dishwasher. you should find the tech data information sheet attached to the backside of the kickplate, in a plastic bag, if it hasn't been lost or misplaced. This dishwasher circuitry isn't too complicated, as long as there is power to the dishwasher and the door is latched, there is 120 VAC supplied to all the components in the dishwasher. The control board controls the neutral leg of the circuit in order for the motors etc. to operate. You will need to check the wiring harness, especially the gray wire from the control board to the drain pump for shorts or pinches to the frame or cabinet. Especially at the bottom of the door/ and in the door liner. If all's OK, the control board would be the next and best option. Read More...
Manoj May 25, 2014 for Model Number mdb8600awq My Maytag dishwasher works well but it does not drain water. i checked the bottom and drain pipe, nothing is clogged. I also changed Wash Impeller Assembly. Dishwasher does not drain.
1 Answer Manoj, You do have a separate drain pump WP6-917641 located in the right rear area of the tub. you didn't mention if you could hear the motor running or not, but the test isn't that hard to perform. The test information is listed on the tech data information sheet located in a plastic bag taped to the backside of the kickplate panel. Drain Pump The Drain Pump will drain water from the Dishwasher in various cycles. If a failure is suspected, the entire Pump Assembly needs to be replaced. 1. Disconnect power to the machine. 2. Remove Support and Toe Panel. 3. Disconnect lead wire from Pump Assembly. 4. Disconnect drain hose from Pump Assembly. 5. Remove Torx™ screw through bushing in Pump Mounting Plate.6. Rotate Pump Assembly to unlock from Tub. It can be difficult, but in most cases you can access and remove the drain pump from the dishwasher without removing the dishwasher from the cabinet. Read More...
Mj February 11, 2014 for Model Number MDB7601AWW My dishwasher fails to drain usually on the last drain cycle about once every 3 weeks, between those 3 weeks it operates fine. I have checked the tank, drainage pump, drainage hose and filters and all are clean and the hose has no kinks in it. One time that it failed to drain I happened to be close by and I could hear a sound of a motor but water was not draining into the sink.
1 Answer MJ, you'll need to remove the pump cover and lower spray arm and remove and check or replace the drain pump baffle WP6-919119 . If or when the "flaps" of the baffle get deformed or bent they create a vortex and the tub will not drain. Read More...
Art February 02, 2014 for Model Number Maytag quiet series 100 dishwasher When dishwasher is complete, there is about 3/4 of an inch of water left in the bottom of the dishwasher. What's up with that?
1 Answer Hello Art. Check and see if the pump is clogged. We will need your model number to help you more with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
William August 27, 2013 for Model Number MDB7600AWW I am having trouble with my Maytag Model MDB7600AWW dishwasher. When I put the machine on after about 1 minute it shuts down. I find the tray inside is filled with water. When I try a second time the same thing happens. However, on the third try the machine runs fine. At the end of the wash there is no water in the tray. This pattern has been happening for about a week now. What should I try?
1 Answer Hello William. Based on the information you provided, it sounds like the control board 99003160 is bad and will need to be replaced. Read More...
Lamar August 20, 2013 for Model Number MDB8600AWW I can't get the bracket, (number 17), to seat properly on the pump.
1 Answer Hello Lamar, Try removing both from the unit and fastening the bracket to the pump off of the unit and then installing the two as an assembly. Read More...