Matt May 11, 2022 for Model Number MagicChef XXXX-2XUB I wanted to confirm this element works with my in-wall MagicChef oven? I can only find the last 4 model numbers of the oven "2XUB" The look, fit, and size are all the same, 2 vertical connection terminals. The oven does say this bottom element should be rated for 2.7KW. Part Number 04000047. Thanks!
1 Answer Matt, According to the partial model number, the bake element will be WPY04000066. Read More...
Lisa April 07, 2021 for Model Number Magic Chef 9512wuv wall oven When I removed the heating element the wires on the back will not disconnect. How come they don’t slide off like the video shows?
Lance February 05, 2021 for Model Number CWE5800ACE Based on my replacement element I would assume that after I remove the two screws I should be able to life the enclosed wiring behind the plate to release the current element. It did not work.
1 Answer Hello Lance, sometimes the wires attached to the element terminals are very short and do not allow access to them from inside the oven, in that case, the oven has to be unmounted and the back panel removed to access the wiring. Read More...
Lance February 05, 2021 for Model Number CWE5800ACE Based upon the new element that I received, I would assume that to remove the old element, I would have to push the enclosed wiring up to release the old element. I cannot get it to move. Am I doing something wrong?
1 Answer Lance, The wires for the element screw into place and you would need to remove the screws and then you can pull the element out and install the new one. Read More...
Marc January 19, 2020 for Model Number Magic Chef Self Cleaning Double Wall Oven 24" 1960's I removed the broken bake element from the upper oven and it had a 3-wire setup. Two of the wires had standard spade connectors and were removed easily. The 3rd wire (ground?) was attached to a small metal plate on the right side of the element. The plate had a larger hole in it that the element went through. It also had a smaller hole for a screw terminal which the wire was wrapped around. This 3rd wire is stranded wire. The new elements only have the two spade connectors. What do I do with the 3rd wire? Should I solder it to the element? Do you sell those metal plates with screw terminals? Or can it be attached to the wire on the right side and run through the same spade connector?
1 Answer Hello Marc, early range/stove production had a separate ground wire for the oven element, That is no longer used as it is grounded through the mounting screws now. Read More...
Tom February 01, 2016 for Model Number Jenn-Aire Expressions drop in This oven is 18 years old, it just started yesterday to take a long to time to heat, and it never got to the requested temperature. Could this be the heating element going bad?
1 Answer Hello Tom/ Yes, you will need to check the elements in the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Roland D November 30, 2015 for Model Number 961-3LCX Can you confirm the correct heating element for my oven. This is a 2 oven Wall unit and the oven element is not working. The lower oven and broiler still work fine but I need to replace the upper oven element. It is 16.5" x 16" and 43 years old. The site crosses it over to Y04000066. Is this correct?
1 Answer Roland, The bake element for your unit is part number 1938261 which unfortunately has been discontinued by the manufacturer with no suitable replacement. Read More...
Chris November 11, 2015 for Model Number 1950's in the cabinet magic chef wall oven My element has the two clip endings, but also a third wire. What do I do with the 3rd wire? None of the videos I have seen have 3 wires. Thanks!
1 Answer Hello Chris. Two wires should be the same color and 1 different. 2 same goes to 1 terminal and the different goes to the other terminal. Read More...
Susan B August 08, 2015 for Model Number Majic Chef wall oven 878-86XWW Do they still make baking elements for this wall oven? I can't afford the 3 - $4,000 to replace them.
1 Answer Susan, The bake element that you unit would call for is part number WP7406P012-60. Read More...
Condon May 08, 2015 I have a magic chef model number 986Y-4CZ but unable to find that model number and the Bottom element to the oven. I cannot find that model anywhere. Does anyone know?
1 Answer Condon, The part number for the bake element for your unit is part number WP7406P012-60. Read More...