Brad July 14, 2018 for Model Number ED5PVEXWS02 The Everydrop 3 filter will not lock into place and stay regardless of the amount of pressure applied. The PUR filers that was previously installed fits correctly. Any suggestions on how to resolve the problem?
1 Answer Hello Brad, You will most likely have to replace the filter housing WPW10121138 since it sounds like it has an issue. Read More...
Lori June 18, 2018 My replacement filter - Every drop 3 - replacing PUR 4396710- The filter will not pop into place. I have never had a problem changing them before but this one will not click into place. Any suggestions. Whirlpool Ref. model #ED5PHAXSQ01
1 Answer Lori, This filter will fit into the filter housing the same way as previous and would suggest to use something and give it a good push with leverage on it. Read More...
Steve May 12, 2018 I’ve replaced my "every drop 3" filter in my life Whirlpool refrigerator about three weeks ago. Followed instructions. Now the water has quit dispensing. I can remove the filter and reinstall, but this only helps for a few hours. Have I installed it wrong?
1 Answer Hello Steve, This is most likely going to be a bad filter head that the filter installs onto. I'm sorry but we will need to ask you to post a new question including the model number from your units' I.D. tag so we can recommend parts that can be guaranteed to work properly on your unit. Thank you for your patience and understanding in this matter. Read More...
Rocky April 24, 2018 for Model Number WRS325FDAM02 My water filter did not pop out when door was opened, I have tried pulling and other ways, any suggestions.
1 Answer Rocky, Try this Try closing and re-opening the Water Filter Compartment Door. Ensure the door is fully opened. Turn off the water to the Refrigerator and purge some of the water from the water line line, using the water dispenser. Dispense several cups of water, this will release some of the water pressure in the water line. After purging the water line, try removing the water filter. You should be able to "feel" the door engage the tabs on the filter and begin to move out of the housing. The last resort would be to remove the kick plate panel, then use tools to carefully extract the filter from the housing. Read More...
Rocky April 24, 2018 for Model Number WRS325FDAM03 The filter did not pop out when door open, I have tried everything to get the filter out, any suggestions.
1 Answer Hello Rocky. Press the filter back in and then press the release again to see if the filter pops out like it should in the unit. Thank you. Read More...
Jaime April 17, 2018 for Model Number KSCS25INSS00 What is the replacement water filter for my KitchenAid refrigerator, KSCS25INSS00? And do I need to turn the water off when I replace it? Thanks.
1 Answer Hello Jamie. EDR3RXD1 is the filter needed. There is no need to turn off the water to the unit. Thank you. Read More...
Mr.T February 27, 2018 for Model Number MSD2542VEBOO I have model EDR3RXD1 and when I replaced the filter, it worked for a few glasses, and then it slowly went to a trickle and stopped working. I put my old filter in and it works fine so I put the new one in and tried again with another new filter same results but this time it broke the water valve so I had to replace. I put the new filter in with the new water valve and same thing slow water I put my old one in and good water pressure. I know its not any frozen line because I had it unhooked for a whole day and a half I know its not the filter housing because if it was how and why would it only work with my old filter which my old filter is the same mode EDR3RXD1. If it was the water filter housing it wouldn't work with any. So what could this possibly be but the replacement filters I bought
1 Answer Mr. T., It is possible for the filter housing WPW10121138 to "fail". On occasion, the internal bypass mechanism lever can become distorted and wont activate properly with a new filter. You may want to measure the tubes on the end of the filter, they should be the same length and the O rings in the same position on both old and new filters. If not you may want to try a different parts source for the filter. Read More...
Shrega February 03, 2018 for Model Number EDR3RXD1 I have model EDR3RXD1 and when I replaced the filter, it worked for a few glasses, and then it slowly went to a trickle and stopped working. The water flows from the dispenser fine when the filter is removed. It's almost like the filter is pinching off the water supply, the reservoir is emptied, and then there's no more water. The old filter, same model, worked fine, and this is the second replacement filter with the same result. Does this make sense? Do you know what's wrong?
1 Answer Shrega, You forgot to include a model number for the refrigerator, or mention a problem with the ice maker making ice. If the water tank/reservoir in the refrigerator compartment isn't frozen, then the most likely issue is the bypass system, inside the filter housing assembly WP2186443 has "stuck" and will not allow the water to flow through the assembly and out to the dispenser/ice maker. As long as you're sure you're installing and seating the water filter properly, you'll need to check, replace the filter housing. You'll need to model number of your refrigerator to order the appropriate part. Thanks, Read More...
Fred B December 31, 2017 for Model Number GD5DHAXVY This Whirlpool refrigerator was in my home when I bought it. I found a paper for replacing water filter. It says refrigerator model #GD5DHAXVY. Water Filter #4396841 . What is the correct replacement filter? DO YOU HAVE THEM?
1 Answer Fred, The correct water filter to replace the filter in this unit will be MFM62217204. Read More...