Neil April 26, 2020 for Model Number ED5GVEXVD02 I bought 2 EDR3RX01 filters. I put one in no problem about 3 months ago. It went through the amount, light turned red, went to replace it with the second one I bought. Took the first out, put the second in. Seemed like it goes in and locks, but not set right. No pressure. If I push the filter in farther manually, it works, but release and no pressure. I took it out and locked the first filter in, works just fine still. I replaced the second filter with a new one, same problem. Put the first filter back in for now, locked and working fine. They all look the same, nothing seems different. What is going on?
1 Answer Neil,If the old filter works fine with no leaks when reinstalled then there is a problem with the replacement filter. A little tip, just because the light comes on to replace the filter doesn't mean that the filter is bad, it is only a suggestion to replace. There is nothing reading the water purity and you can save a little money doing this and replacing when your water starts to taste different. It will have a light charcoal taste when you need to replace it. Read More...
Mike April 26, 2020 for Model Number ASD2522WRB04 I removed and replaced water filter and I now have water leaking out of the filter compartment. Looking for some help!
1 Answer Mike,Remove and replace the filter once again to see if the leaking stops. If not try putting the old filter back in and see if it leaks. A seal could be bad internally in the housing and possibly need to be replaced. WPW10121138 Read More...
Earline December 30, 2019 for Model Number msd2572veboo Where the ice comes out to go into the tray on the door, it freezes with this hunk of ice. I do need to change the filter. Could this be the reason for the ice around the bottom where the ice cubes come out to go into the door dispenser.
1 Answer Earline,The reason for ice build up is air leaking into the freezer door. The moisture in the air turns to ice when entering a frozen environment. As long as the tabs for the ice door are not broken off then you can use this kit W10823377. If tabs are broken and the assembly can be moved left to right and not sealing because of this then you will need to order 8201756. There are videos on our web page under both part numbers to help with the repair. Read More...
Katherine September 22, 2019 for Model Number side by side refrigerator GS5DHAXVY01 What water filter replacement is compatible?
1 Answer Hello Katherine, the compatible water filter for the model number supplied is part number EDR3RXD1. Thanks! Read More...
David July 02, 2019 for Model Number 795.79304.901 Needing a Replacement Filter for a Kenmore Refrigerator. Not sure which filter is needed. Thanks for any help with this.
Janice May 24, 2019 ED5LHAXWB00 The bottom section of the in door ice maker cannot be removed. All the ice is gone and the bottom on the right that says to push up and remove the box can be pushed but the container does not unlock with much pulling. It seems like there is still something keeping it attached near the middle.
1 Answer Janice, Open the ice door on the dispenser and look up in there to see if there is ice caught in the chute. If there is then this is what is causing the ice bin to not come loose easily. Also try taking a hair dryer and blowing under the ice bin, do not leave for too long as this could cause the liner to melt but this may help with removing the bin. Read More...
1 Answer Hello Marilyn, This filter EDR3RXD1 is the one listed by the manufacturer as the proper replacement part for the model provided. Read More...
Liza November 01, 2018 for Model Number ED5LTAXVL00 My landlord just replaced our broken refrigerator with this previously owned 2008 Whirlpool. Id like to change the filter but it appears the filter cap is missing and I can't seem to get the filter to eject. Do I need this cap in order to get the old filter out? Or is it possible that something is broken? Thanks!
1 Answer Hello Liza, This WP2260518B is just a decorator piece. The filter can be removed by removing the kickpanel and turning the filter. If you need to you can grasp the old filter with a large pair of pliers to get it to turn. Do not use pliers on the new filter since this could cause a leak. Read More...
Jeffrey October 19, 2018 Will the EDR3RXD1 or EDR2RXD1 work as a replacement for a (Whirlpool) refrigerator that now has an EDR1RXD1 installed?
1 Answer Jeffrey, Neither of these 2 filters will replace EDR1RXD1. You will need to use this one for your unit. Read More...
Scott August 02, 2018 for Model Number Original Whirlpool Water Filter EDR3RXD1 Does the water need to be shut off during filter replacement?
1 Answer Hello Scott, If the filter head is operating properly, the water will not need to be turned off during the filter replacement. Read More...