Saad March 11, 2012 for Model Number MDG7600AWW I am having a problem with my Maytag clothes dryer. Of recent, the clothes are not drying. It now takes three cycles when it use to take one to dry a load of laundry. Also, after those three cycles, I noticed the laudry is cool not warm when it comes out. The dryer is not set to a cool mode to have this unwanted effect. In adition, with the Maytag Atlantis I have difficulties locating the ingnitor/flame door/pannel to view the flame. Do you suggest removing the front pannel so as that the flame can be directly visualized? Please provide any suggestions to view the flame with corresponding diagrams and all other advise to resolve the current "non Drying" problem. Thanks!
1 Answer Hello Saad. You will need to remove the front panel from the dryer and run it and see if the igniter 4391996 is working and the gas is lighting. You will remove the door and then remove the front panel. Reinstall the door and run the unit. Hope this helps. Read More...
Melissa January 29, 2012 for Model Number ldg312 My dryer willl not heat and when I open the small door in front it is not lit up at all.
1 Answer Hello Melissa, if your igniter is not glowing a bright white you will need to replace it. The correct igniter is 4391996, if it ignites and shuts off in a few seconds it could be the coils 279834. Thanks! Read More...
1 Answer Hello Frank! The dryer igniter 4391996 is listed as a cross reference to the original ignitor used on your appliance, 5303937186. The part should work since it is listed as a cross reference however, it may require adjustments to fit your unit. Please keep in mind it is suggested to replace the parts called directly for your unit. Thanks. Read More...
Art October 02, 2011 for Model Number maytag ldg7500aaw The circuit breaker for my gas dryer was poped off. I reset it now, dryer runs but no heat. Igniter does not glow. Did igniter or coils short out breaker? Does not pop now..
1 Answer Hi Art. Yes, the igniter can open and not create heat. It is part # 4391996. The coils are very much known to short out. Part # is 279834. Thank you. Read More...
Tony September 28, 2011 for Model Number mdg3000aww after washing rags used for waxing my boat and thinking they were clean, i put them into dryer and now the heat wont activate. everything works fine, dryer spins and does all it should except now i cannot get heat to come on. im hoping someone familiar with maytag neptune dryers can point me to which part wouldve been affected, thank you
1 Answer Tony, There are several components involved, but they can all be accessed from the front of the dryer. You will need to remove the four screws on the inner lip of the door opening of the front panel(two on each side of the opening) slightly raise the door to release the hinges from the front panel, and set it aside, Grasp the upper portion of the "goal post" portion of the front panel and pull out untl the panel releases from the hidden retiner clips, lean the panel out ,at the top and lift the panel off the bottom retiner clips, and set aside. Re install the door(you don't have to install the screws) and start the dryer in a heat cycle, observe the ignition procedure : igniter should glow red, in a few seconds the igniter should start to fade and the gas released and the burner ignite. Let us know what occurrs and we can get you going from there, you will need a multimeter to test circuits and voltage. Thanks and Good Luck Read More...
Gary September 13, 2011 for Model Number whirlpool-gas-lgn2000pg1 Sorry. Here is the brand and model.
1 Answer Hello Gary. Based on the information you provided, it sounds like the coils 279834 are bad and needs to be replaced. Hope this helps. Read More...
Gary September 13, 2011 My ignighter comes on and gas lights then goes out after a bit. Then it will not light again during the cycle (even though the ignitor glowes red). I changed the ignitor, still will not work. What to do next?
1 Answer Hello Gary. What is the model number of the unit your working on? Thanks. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Carlos C. August 24, 2011 for Model Number LDG4914AAM My dryer stop drying clothes. Spins and timer works, but no heat. We replaced the coils a few months ago. I was told that it was the heating element. Looked up heating elements online and did not find any element on my unit but did find it has an igniter. Is that the part I should be replacing? Does my unit have a heating element?
1 Answer Hello Carlos. No, your dryer does not have an element, it is a gas dryer. You will need to test and see if there is power going to the igniter. If so, and the igniter does not work, you will need to replace the igniter 4391996. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
1 Answer Chuck, Yes, the voltage to the igniter is 110 to 120 VAC. The gas valve coils help to vcomplete the circuit.Thanks and Good Luck Read More...
John H. July 28, 2011 for Model Number MDG 4000AWW Our dryer was in use during the latest power outage, and after the power came back on, the dryer was still on, spins, and the light comes on, but there is no heat. Upon looking the igniter does not glow. Does this mean I should replace the igniter, or is there anything else I should look at?
1 Answer Hi John. If your dryer is not giving any codes, then you will need to replace the igniter. This part # is 4391996. Thank you. Read More...