Genna June 03, 2018 for Model Number MFI2269VEM7 Does Icemaker Assembly part number AP6037857 (WP10882923) include the Icemaker Cycling Thermostat part number AP6010137 (WP627985), or must the Thermostat be purchased separately?
1 Answer Milton, You will want to check to see if there is voltage of 120 vac getting to the water valve. If there is proper power then the valve would most likely be the issue. Read More...
Jc May 03, 2018 for Model Number GI6FARXXY08 Recently changed the cycle thermostat, but after 2 months working, not getting Ice again. Would there be some issues partially solved with a thermostat replacement, when really needing a replacement of the IceMaker Unit?
1 Answer Hello JC. Make sure the freezer is 0-5. If so, then it is possible the icemaker is bad. Also, check the fan for the air and the ice box sealing good. Read More...
Tom A, February 16, 2018 for Model Number new style whirlpool ice maker # w10882923 Where is cube size adjustment screw on this ice maker #w10882923 whirlpool
1 Answer Tom, When you remove the cover on the icemaker it would be on the side. The adjustment will most likely not make much difference in cube size. Read More...
Kenny January 25, 2018 for Model Number GZ25FSRXYY2 New ice maker replacement comes with new wiring harness. Ice maker blower motor has two wire connector , new harness has three wire connector.. What is the proper way to connect the blower motor using the new harness? Harness Model #W10312697 rev B Thank you.
1 Answer Kenny, This icemaker kit comes with 2 different wire harnesses and instructions for the installation. You will want to use the harness that is for the 25 cubic foot model refrigerator which should have all the same connections. Read More...
Rob December 03, 2017 for Model Number g16farxxy08 I've replaced the ice maker on my g16farxxy08 with the ice maker model W10882923. I'm still not getting ice. I've also replaced the fill valve, and not getting any ice. I've tried the jumper wire but that doesn't seem to do anything either, maybe i'm jumping between the wrong points? Anything I can do to confirm it's the ice marker and not some other board inside the fridge?
1 Answer Rob, You will want to check to make sure that the fill tube is not frozen. If the fill tube is frozen then will need to be thawed. If it is not frozen then this will be a faulty main control board that would cause the icemaker to not work. Read More...
Ray S July 22, 2017 for Model Number wrx735sdbm I have replaced original ice maker with part no. w10882923. Which way do I turn adjustment screw to make cubes smaller?
1 Answer Ray, You would turn the screw counterclockwise but will not want to turn more than a 1/4 of a turn either direction. Read More...
Aaron July 21, 2017 for Model Number GI6FARXXY08 Does this part include the motor module or is this everything from motor model back?
Michael July 01, 2017 for Model Number gi6sdrxxy07 I see that there are 2 wiring harness that come with the icemaker. Do you have to replace the whole wiring harness? That looks like a tough job. do you have a how to do video on that?
1 Answer Michael, Yes you would want to replace the wiring harness with the icemaker. Unfortunately there is not a video on doing this but should not be real difficult to do. It should come with instrucitons. Read More...
Mark June 24, 2017 for Model Number MFI2665XEM7 Paul, I am replacing the ice maker on my Maytag refrigerator. The original part number was W10377151. The replacement part number is W10882923, which requires replacing the wiring harness. Everything is fine, except I'm not sure which way to plug in the orange connector. With the ice maker sitting in the upright position, do the white wires on the connector go on the right side or the left side?
1 Answer Paul, We do not have information on which side the white wires of the connector go on but would say the left side. Read More...