Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Rotor Position Sensor Kit by Whirlpool

Best Seller
Manufacturer Part
4.89 (64)
By: Whirlpool
Part Number: OEM12981945
Manufacturer Part Number: W10183157

Questions & Answers

For Whirlpool Rotor Position Sensor Kit (Part Number: OEM12981945)

Hank for Model Number wtw6600sw

I have 2 1/2 months left on the warranty. I still get F51 errors..after tech replaced RPS sensor, control board, & harness. I notice when I get the F51 it is at the very start when the motor is "supposed" to rotate the tub. I get around the problem by unplugging power, wait, plugin pwr to release unlock lid, and manually check rotate tub to verify it is NOT binding/dragging - and it is not. Replug the washer and "it works". QUESTION: Is it possible the "stator" (or motor whereever it is) has a 'bad spot' on the magnet or stator the prevents the motor from rotating ..and.. that 'bad spot' occasionally ends up at a position where the tub cannot rotate (causing the F51 code error + absolutely no movement in the tub at the beggining of the wash cycle) ???? Any feedback would be GREATELY APPRECIATED !! Thank you!

1 Answer

Hank, the other possibilities are : something very small could be stuck between the tubs, The washer spin basket is not raising properly, possibly a low water level or the tabs on the drive gear under the agitator is not dis engaging, and causing a drag on the motor causing the F51 code. You'll need to raise the top, remove the tub cover, agitator and spin basket to check. Thanks and Good Luck.

Read More...

1 Answer

Hello Robert. You will need to check and make sure the tub turns freely by hand. If it is tight, you will need to check for something between the inner and the outer tubs. If it is free, you will need to test the motor. With an ohmmeter, check for continuity
between all pins on the P5 machine/motor
control connector and the drive motor
connector.
? If there is continuity, replace the drive
motor.
? If there is no continuity, replace the lower
machine harness.
If the motor is good, you will need to replace the control board WPW10189966. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps.http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Read More...

1 Answer

Hi Michael. You might have to replace the board part number WPW10189966. This is what sends the message to the motor to go into spin mode when it's in spin cycle. Hope this helps!

Read More...
Jerry for Model Number 110.27092600

My Kenmore Elite top loading washer (with glass lid) wobbles out of control when it reaches the spin cycle and shuts down with UL (unbalanced load) indicator. The springs and hanging rods are okay and in good shape. There is a L shaped metal counterweight fastened to the underside of the plastic outer drum. Is it possible that the load positioning sensor is defective? Does this sensor adjust for counterbalance? I have no other codes displayed except for the UL code when it wobbles out of control.

1 Answer

Hello Jerry. Check and make sure nothing is between the inner and outer tub. Also check and see if the tub bearing is good. Hope this helps.

Read More...

1 Answer

Hello, The only way to replace the tub bearings for this model is with a new outter tub assembly. They do not sell the bearings separately. Here is the part number for the tub assembly. W10193886

Read More...

1 Answer

It sounds like you are still in the diagnostic stage of your repair. We have a Repair Forum on our website and it would be better for you to ask this question in that venue. You may be able to find an answer by searching in the washer section or you can post your own questions. Be sure to provide your model and serial numbers. Here is the link http://forum.appliancepartspros.com/ Thanks!

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google