Anthony February 07, 2023 for Model Number MGT8775XS01 I bought a used Maytag Gemini (MGT8775XS01) which was converted to LP by the previous owner. I need to switch it back to nat gas, but can't find orifice spud & hood part numbers for it anywhere (five range burners, two bake burners and one broiler burner). Would you happen to have them? Thanks!
1 Answer Anthony, To convert this unit back to natural gas you will need to get the orifice holders right front and rear WPW10407679, left rear and center WPW10407680, and left front WPW10407681. For the oven, you would need the broil fitting W10292293, the upper bake orifice W10342662, and the lower bake orifice W10342661. Read More...
Joe November 09, 2022 for Model Number Kitchenaid KGSC308LSS0 Received part WP9755424 and need to convert it to LP (propane). I have the Kitchen aid conversion instructions that describe turning over the "regulator" dohickey (under white cap) and reinstalling it. But, I find the brass orifice fitting (13mm hex) going to the oven is quite reluctant to turn. I am hesitant to proceed as it does not seem reasonable to force it. I've done a bit of mechanical work and this feels a bit like "better stop before you snap it off". Been through this before but do not recall it being so reluctant.
1 Answer Joe, the orifice hood may already be tightened down. This can be identified by loosening the orifice hood 2 full rotations and then tightening it until it is just snug. It is correct that the orifice hood should not be overtightened as this can damage the pin under it. Read More...
Randall August 26, 2021 for Model Number SF379LEMS0 I purchased this oven/range and the previous owner disposed of the LP conversion kit. I'm trying to track down the correct size for the LP orifices to convert to LP. I have the factory rating label for the BTUs for the burners but that's not enough information. Apparently the only conversion kits shown as compatible only include 4 orifices for the top burners but not the bake and broil orifices. They also appear to be no longer available though I have found a few people who might have them. Is there any way to find out what the correct six LP orifices are so I can buy them individually if I can find them?
1 Answer Randall, For the oven you do not need to change the orifices, you just adjust them by tightening them down 1 1/2 to 2 turns. Unfortunately, on the top burner orifices, we do not have any size information for them. Read More...
Kevin June 07, 2021 for Model Number KGST307HWH4 Purchased kit to convert Nat to LP, need instructions please. Thank you. Part number for kit purchased 9755428
J September 01, 2020 for Model Number Model WFG510S0AS0 Looking for the orifices to convert my LP stove back to natural gas, are there any available parts for model WFG510S0AS0?
1 Answer Hello J, if the original Nat gas orifices were lost when converted from Nat to LP gas,, the individual parts needed to be ordered because there is no kit for converting back from LP to Nat gas, parts are as follows, cooktop burners ,LF WPW10185023,,,RF WPW10170508,,LR WPW10170508,,,RR WPW10170506,,Broil burner orifice with fitting W10853603,, Bake burner orifice with gas valve.WPW10602001. Read More...
Jessica June 19, 2020 for Model Number YKGRT607HB6 I have the conversion kit WP9755428 but it did not come with any instructions to know which orifice go to which burner, can you please advise?
1 Answer Jessica, the LP conversion instructions will be sent to you to assist with this process. Read More...
Gerardo June 16, 2019 for Model Number WFG515S0ES1 WIl the conversion kit wit the part #AP6013930 fit on my gas range? I want to convert my stove to function with propane gas instead of natural gas. Also other than switching the spuds do I need to replace anything else.
1 Answer Hello Gerardo, for the LP conversion you would need part WPW10170534 LP kit for the cooktop , and part W11126051 LP kit for the bake/broil burners.You will also need to adjust the pressure regulator for LP gas supply and and adjust the oven burner's air shutters. Read More...
Ben May 10, 2019 for Model Number wfg374lvb What parts are needed to switch a whirlpool wfg374lvb from LP back to natural gas?
1 Answer Ben, you will need the stove top orifices: left rear [WPW10170508], right rear [WPW10170506], left and right front [WPW10170509], and center [WPW10170507]. Read More...
Cynthia Aubrey December 26, 2018 I purchased part # 9755428, WP9755428 SPUD ORFCE but lost my instructions. Can you email me instructions?
1 Answer Cynthia, We will need to have the model number of your range to be able to assist with LP conversion instructions. Read More...
Kurt K November 09, 2018 for Model Number WFG505M0BS0 I have the conversion kit, but it did not come with any instructions to know which orifice goes to which burner, can you please advise?
1 Answer Kurt, On the orifices there should be paint marks. There will be 2 with yellow/black and should have number 88 stamped on it which will be for the center and left rear burners. There will be 2 with yellow/orange paint and number 116 stamped on it one for the right front burner and one for the left front burner. There will be 1 orifice with a yellow/white paint and number 70 stamped on it which goes to the right rear burner. Read More...