Ralph January 02, 2023 for Model Number Kenmore Model 110 Can the door switch be re-set after it has popped open due to unbalanced load?
1 Answer Ralph, If the door switch has gone bad it cannot be reset and you would need to replace the switch. Read More...
Lee May 15, 2022 for Model Number stewart_prather@msn.com I have a whirlpool duet ghw9100lw......No lights, wall socket getting power. CCU is probably bad. However i have clothes in the washer and would like to get them out....Door is locked shut. Is there a way to open the door from the top if i remove it? I was standing next to machine when it shut off. Made the usual click sound. The display went dark and the door is locked?
1 Answer Lee, Remove the lower access panel on the front. Once it is removed, reach up to where the lock is and there will be a round piece at the bottom of it that you will pull down on and this will release the door lock. Read More...
Wp_Fan1 January 12, 2022 for Model Number GHW9300PW0 Getting a "DL/F" error. Door latch will not engage and therefore, washer will not start cycle. Can hear faint clicking noise, like it is sending signal and wants to initiate cycle. It clicks ~5-6 times then beeps and displays the "DL/F" error code. I replaced the Door latch assembly (QED thanks to your helpfull video). However, still get same results, does not start, and then "DL/F" code. Any recommendations would be greatly appreciated. Do I need to check the Wire Harnesses? and/or some control electronics? Thx
1 Answer WP_fan1, if there is not a pinched/broken wire, loose connection, and the door is able to properly close, the failure would be in the main control WP8182308. Unfortunately, this part has been discontinued and is no longer available. Read More...
Thomas February 21, 2021 for Model Number 11045081404 Washer will not start at times after depressing the start. Sometimes have to depress the start for a long period of time. Is the door switch or control board defective? How can the door switch be tested? Thanks
1 Answer Thomas, Most of the time you will find that the plastic tab for the start button has broken off and not contacting when you depress the start button. Unfortunately, this part is no longer available and no satisfactory replacement has been provided by the manufacturer.8182248 This is the manufacturer part number, you can try a google search to see if you can find one available online. Read More...
Don January 16, 2021 for Model Number ghw9250mt2 getting a "dl" error code. washer stops just before final spin I cant get door to open, clothes are stuck in washer
1 Answer Don, Based on the information provided the DL error is a door lock error, sounds like the door latch assembly would need to be replaced. Read More...
Doc November 09, 2020 for Model Number KHWS01PMT2 Am getting F11 code and when messing with the machine it messes with the door switch. while trying to get it to go away I get a door lock code also... I changed the door lock and it worked thru 5 washes and then started doing the same thing. starts with the F11 when it reaches drain and spin on the timer. I checked all the connections and they all look good. Cleaned the filter trap also. Could you help with the next thing I should do.
1 Answer Hello Doc, the fault code F11 refers to the main control board not being able to power or communicate with the motor control board when this occurs the main control will not allow the door latch to unlock for several minutes for safety, if you try to force the door to unlock in that time through the control panel you can get a false lock fault code ,the motor control board is part W10756692. Read More...
1 Answer Hello Doc, the fault code refers to a failed Motor Control Unit, W10756692, when this part has failed and the washer attempts top to start, the main control board will go into a safety lockout and not allow the door to unlock for several minutes. If there was a latch problem it would have a different fault code. Read More...
Dylan April 25, 2019 for Model Number 461970200691 How do you test a door lock to see if it is broken?
1 Answer Dylan, The model number that is listed does not come up as a good model number and we would need the model number of the unit to be able to assist properly with your question. Read More...
Elizabeth November 12, 2018 for Model Number 11045091400 I changed the door switch assmbley because that is what the error code said n it is still toping and saying that f/dl. what do i do know. it also has f11code.
1 Answer Elizabeth, the F-11 error code is a communication error between the main console and the control board. Sometimes you can unplug each connection at the board and plug them back in and it will fix the problem, if not, you will need to replace the main control, part number is WP8182689 Read More...
Amanda September 29, 2018 for Model Number Maytag I have a Maytag front load washer. The problem I have is it will go through a complete cycle but the door will not unlock. I have replaced the lock switch part number WP8182634 about 2 months ago, it was working fine. Now it is doing it again. Could it be something else that is causing this problem? I unplug the washer and plug it back in, it doesn't unlock it. That would work a couple of times before. I put it on the spin and rinse quick cycle as soon as I start the washer it will unlock it. I hit pause and stop the cycle that is what I have been doing to be it to open. Could I get help please? Thank you!
1 Answer Amanda, Yes, there are a couple of things to check, first. Make sure the loading door is aligned to the opening in the front panel, check the door latch mounting screws to make sure they are tight and the latch is properly mounted and secured to the front panel. Check the door latch strike, on the door, make sure it is installed and tightened properly. Lastly, check the wiring at the door latch assembly and the control board for loose connections, and check the wiring for any sharp crimps, twists, kinks, etc. Read More...