Charmaine October 12, 2018 for Model Number WTW8500C0 I need a lid latch assembly and was given this number OEM Part # WPW10619844 Is this the part I need ?
Nick47 September 17, 2018 for Model Number WTW6200SW0 Hello. My door latch broke. I ordered a new one. A different part showed up with no holes to mount the new one. The old part was w10059230 The new part they sent is w10619844 I guess my question is, did they send me the right part and if so how do I mount it? Thanks for any help
1 Answer Nick, The WPW10619844 Latch Assembly has been revised by the manufacturer " Be aware the manufacturer has updated the part and it is now white and clips into the main top without mounting screws". Yes, you have the correct lid latch switch assembly. Read More...
Vincent February 05, 2018 for Model Number WTW7600XW0 I need to double check lid latch part # for this model before ordering. Also i am getting an error code F80, will this part fix this code. Washer does not spin. Thanks
1 Answer Hello Vincent. You will need to order WPW10619844 for your model. The code is for the following conditions occur:? Lid is not closed completely due tointerference.? Check for lock interference with lid or lockbezel.? Wash media buildup is preventing the lockbolt from extending.? Machine/motor control detects open lidswitch when attempting to lock.? Machine/motor control cannot determine iflid lock is in a locked state. Read More...
Eve October 30, 2017 for Model Number MVWB725BW0 maytag Bravo XL Hi, I need a latch, several part numbers including a whirpool part number pops up. Are they interchangeable? Which one do I need? Thanks for the help!
1 Answer Hello Eve. Based on the model number you provided, you will need to order and install WPW10619844 for your unit. Thank you. Read More...
Ray October 14, 2017 for Model Number MVWB750WQ2 My washing machine gives a DL code. Is the the correct lid latch for this model?
1 Answer Ray, Yes the latch assembly WPW10619844 will be the correct part for your unit. Read More...
Adam July 18, 2017 for Model Number W10410358A Which lid lock should I get? I performed the diagnostic manual test and it was determined that I need a new lid lock piece? I want to make sure I get the correct part.
1 Answer Adam, The model number you supplied [W10410358A] is incorrect or incomplete. We will need a complete model number and serial number to assist you properly. The part number you supplied WPW10619844 is for an "older" Whirlpool "Cabrio" washer, (WTW6******). The switch assembly is a pretty common part for Cabrio style washers and may be the correct part to order. Read More...
Joe March 13, 2017 for Model Number MVWB300WQ2 Replaced lid lock with WPW10619844. Still getting error: dU Any ideas or suggestions. Seems like it should be plug and play.
1 Answer Hello Joe. Make sure the wiring is connected good and if so, you will need to replace the control board on the unit. Read More...
John January 27, 2017 for Model Number MVWB800VQ0 Our Maytag Bravo top loader has the dL error message flashing. A repair man came out and said the door lock was bad. I looked up the "latch" on your site and found the replacement part. Before I order it, can you please confirm the right part number?
Susan December 14, 2016 for Model Number WTW6800WW1 Was getting an error code of dl on the washer so we replaced the lid locking mechanism. The unit still will not lock properly, and will not function properly. What else can we look for? It stopped working with a full load of clothes in it. It stopped after the wash cycle, and was flashing dl. I emptied washer of wet clothes and tried using after we replaced lid locking mechanism. It locked and started to run water but would not spin, and the started flashing dl again. Any information you can give would be greatly appreciated.
1 Answer Susan, Other than the door lock causing this issue it would be a main control board issue that would cause this issue. Read More...