Jack G September 12, 2016 for Model Number WTW7600XW2 How to replace Whirlpool part W10059230 with Whirlpool part number W10619844? Is this an easy replacement installation? My w10059230 broke and needs replacement.
1 Answer Jack this will install the same as the original even though it looks different. You will want to line up the holes on the lock assembly and screw it in place. Read More...
Joanne September 02, 2016 for Model Number wtw6200sw2 I have whirlpool washer model wtw6200sw2 serial cu0170849 I ordered part wpw10619844 which is suppose to fit my machine. My part on the machine looks like your video, square in shape. The part I got is rectangular, and I can figure how it could replace to fit the part already on. Any suggestions?
1 Answer Joanne, Although the design is different, the hole and opening will align the same way as the old part. You will still install in the same location and run the wires in the same location as the old switch. Line the screw holes up in the same place as the originals. Read More...
Dave September 01, 2016 for Model Number 110.28032701 Our Kenmore Oasis washer is only 6 years old. We don't have a lot to spend because I got laid off about 4 years ago after over 38 years of work & I have been unable to find a decent job since. The other day the washer quit working. My wife tried to work with it with no results. The washer kept giving an error code eventual as simply LID. She stated it initially gave something different, but could not recall what it was. I tried messing with it & turned the power off for some time, etc. One thing that I observed that was alarming to some degree was when I went to plug it back in again after having it unplugged for about 5 minutes that a spark emitted momentarily from the receptacle when plugging it back in. I also observed that the washer lights, etc. stayed on for about 30 seconds or so when I unplugged it at times. Anyway nothing worked to make it work right again & allow us to use the washer. I ran manual diagnostics on it & initially got an error code of F-80. Eventually it also said F-81 & F-82 for just a split second. I think that is supposed to mean the washer lid latch assembly. Does that sound correct? Is it not unusual for a washer like this to start going out at only 6 years. You know we used to keep a washer for years & years & years with no problems. We just don't have a lot of money to mess around with or spend. Do you have any suggestions?
1 Answer Hello Dave. Yes, based on all error codes you listed, the lid lock assembly WPW10619844 is bad and will need to be replaced. Read More...
Martin April 23, 2016 for Model Number MVWB850YWB The lid latch on this Maytag Bravos XL washer went out. Will this one work on this model? This model does not show up in your model search. Thanks
1 Answer Martin, Yes the lid lock assembly WPW10619844 would be the correct part number for your unit. Read More...
Ruben February 08, 2016 for Model Number Mvwb980bg I have lid latch number w10059230 but now it says to use latch number w10619844. But doesn't look any like the old part is that right I also found part number ps10062093 I shoul use. So what part number is it?
1 Answer Ruben, The manufacturer has redesigned the lid lock assembly and will use part number WPW10619844. They may differ in appearance but will still work for you unit. Read More...
Cammy August 15, 2015 for Model Number 10059230 They have replaced my part. Will the new part still fit? It looks a lot different, and now when I close my lid and the power is on, it still says the lid is open?
1 Answer Hello Cammy, If this is a factory substitution, it will work. You could have a bad lid switch actuator or the new part could be defective. If you could please verify the model number from the units' I.D. tag, we can look it up to confirm this is th3e correct part recommended by the manufacturer for the application. Read More...
Kay June 18, 2015 for Model Number mvwb800vq0 This new switch is different from my old one. Can you explain how in the world it will fit?
1 Answer Hello Kay. Although the design is different, the hole and opening will align the same way as the old part. You will still install in the same location and run the wires in the same location as the old switch. Read More...
Curtis C April 16, 2015 for Model Number whirlpool cabrio model wtw5500xw The lid light locks on 2nd click than begins to flash will not continue to next step dormant. Thanks
1 Answer Curtis, You will want to access the tech sheet in the control panel and run a diagnostics test and see if there are any stored error codes. This will tell you where to start on what the problem with the unit may be. Read More...
Terri January 21, 2015 for Model Number MVWB450WQ0 My washer will not start. I have power but when selecting a cycle - then start, the lid doesn't lock right away. I press start again the lid locks, but the washer won't start. Any ideas ?
1 Answer Terri, the more common issue for lid lock and motor issues is a faulty rotary position switch / sensor WPW10178988 If the sensor is producing a false information to the control board, this could cause the lid lock to operate erratically ( may or may not lock or unlock) and the motor won't run. If you can supply a e mail address we can supply some additional information that will be helpful in diagnosing the problem efficiently. Read More...
Frank July 28, 2014 for Model Number 11027092600 I have a Kenmore washer that shows no sign of power when I press the power switch. No lights, no error code, etc. It just appears to be dead. I suspect it is either the control panel or the lid lock switch assembly. The washer has worked fine without issue for five or more years. Do you have any suggestions on how to trouble shoot thus issue? By the way, I have plugged it onto another known to be good outlet to.verify it is not a faulty supply power issue. Thanks! Frank
1 Answer Frank, The first thing to you need to check would be the incoming power to the unit. Check at the receptacle for 120 vac. If there is 120 vac there then you will want to access the control board in the control panel and check where the power cord enters the control board for 120 vac. If there is power then the control board would need to be replaced. If there is not power but power at the wall outlet then the power cord is bad and would need to be replaced. Read More... Safety note: testing, adjusting or bypassing anything while the appliance has power is a job for a qualified technician. Unplug it before you open it up, and keep it unplugged until every panel is back on.