Anthony M. June 02, 2014 for Model Number 110.27032602 I have a Kenmore washer. It has a new lid lock switch. It holds the lid there but there is still some play. Does not pull the lid tight. Could you tell me the problem? Thanks
1 Answer Hello Anthony, If the lid lock assembly is properly installed and the hinge screws are tight, there is probably not an issue since the lid lock is not designed to prevent the lid from moving. Its' only purpose is to prevent the lid from being opened. Read More...
1 Answer Hello Jamie. Unplug the unit for about 30 minutes and then reapply power and see if the unit unlocks. If not, then either the control board or the lock assembly is bad. If you hear it trying to unlock, but does not, replace the lock assembly. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Ray March 17, 2014 for Model Number wtw7340xw2 Like one of the other questioners, I too had a recent severe cold weather problem that caused water valve body to break. Replaced water valve body, but now washer won't power on. Does that mean that I too must replace mother board due to possible damage caused by the water? Other sources seem to indicate that the lid latch switch could be my "won't power-on" problem. Please advise.
1 Answer Hello Ray. Test for power to the board. If there is power there, and the board does not work, you will need to replace the board in the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More... Safety note: testing, adjusting or bypassing anything while the appliance has power is a job for a qualified technician. Unplug it before you open it up, and keep it unplugged until every panel is back on.
Jim February 27, 2014 for Model Number Whrillpool Cabrilo top loader WTW6600sw2 OK How do I lift or remove the top body housing to R / R the lock switch assy. for the lid The grey plastic piece that breaks on everyone has broke. Next Question Why has there not a recall ben issued for this problem after all it is safety lock? Please e mail your response. Thank You.
1 Answer Hello Jim. To install the new latch you will need to raise the main top by releasing the spring clips on both side of the front between the main top and the front panel. You will also need to raise the console which you will use a flat blade on either side under the endcaps to release the spring clip. Lift the console. Disconnect the wiring of the latch and take the screws out of the old latch that are holding it in place. Install the latch in reverse order. Read More...
Jerry February 25, 2014 for Model Number AP3891130,mfg# W10059230 I have a Maytag washer (top loader) and lid wont lock. Looks like on the latch the small dark grey piece between the screw holes broke. Any way I can just replace that piece and if so what is it called?
Robert February 16, 2014 for Model Number MTW6600TQO Recent severe cold weather caused water valve body to break. Replaced water valve body and mother board due damage caused by the water. Washer throws F1 error after minute of operation. What is F1 error code. Need help please. Also possible damage to lid lock mechanism.
1 Answer Hello Robert, On a MTW6600TQ0, the F-1 fault code flashes when the control detects an out of range pressure signal. • Check pressure hose connection from tub to machine/motor control. Is hose pinched or kinked? • If F then 1 repeats numerous times after POWER is pressed and the pressure hose connection is not pinched or kinked, replace the machine/motor control. Read More...
Tony January 29, 2014 for Model Number WTW7320YW0 If I unplug my latch electronic mechanism will the washer return to washing mode or will it still go on to not working mode.
1 Answer Tony, Based on this information it sounds like the latch assembly for your unit is faulty and would need a new latch assembly WPW10619844. Read More...
Mike January 27, 2014 for Model Number WTW6500 I have ordered a new switch lock assembly. Where on the control top does it fit? When I opened the top, it was already disconnected, and there appears to be two possible slots.
1 Answer Mike, The lid lock for your unit will go at the front center of the main top where the lid would come down and wrap over the front. There should be a opening with a bezel there ad the lock will go in this spot. Read More...
Traci January 27, 2014 I have a new Cabrio washer & the "tongue" that comes out to latch the lid is broken. Which part do I need to order? Thank you.
1 Answer Hello Traci. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Jay January 13, 2014 for Model Number wtw5500xwo My washer drains but does not spin dry. I have noticed the lid is not always locked.
1 Answer Hello Jay. Check and make sure the belt WPW10006384 on the unit is good. Also, check the large pulley under the bottom and make sure it is not loose. As for the lid lock, you may need to replace the lock assembly. Read More...