Nicole July 07, 2013 for Model Number wtw5500xw Lid lock is not working do I need a repairman or can I replace it myself?
1 Answer Hello Nicole! You should be able to replace the latch withou a repairmans assistance. To install the new latch you will need to raise the main top by releasing the spring clips on both side of the front between the main top and the front panel. You will also need to raise the console which you will use a flat blade on either side under the endcaps to release the spring clip. Lift the console. Disconnect the wiring of the latch and take the screws out of the old latch that are holding it in place. Install the latch in reverse order. Read More...
Chowell June 17, 2013 for Model Number 7MMVWC300YW0 My washing machine completes all programs. It fills to rinse but does not fill completely for the final rinse.
1 Answer Hello Chowell, This model machine is designed to only fill with 7 inches of rinse water. The only exception to this is if the lid is lifted during the cycle, it will fill with 9 inches of rinse water. Read More...
John April 18, 2013 for Model Number WTW6800WW1 I'm looking for the model number for the latching mechanism on the unit to lock the lid. The grey tab was broken off when I bought it used. The unit number is WTW6800WW1. Also, how do I replace it?
1 Answer John, if you are needing the actual latch/lock mechanism you'll need part numebr WPW10619844. This latch uses a magnet inside the lid WPW10183521 to lock. Thanks! Read More...
Teresa February 18, 2013 for Model Number wtw6300ww0 my washer will start and stop inthe middle of cycle and say ld and it will not do any thing else even if i unplug it and plug back up i can not get it to go into a rinse and drain cycle now i got eater sitting in the tub
1 Answer Hello Teresa, You will want to check for a clogged drain pump and hoses. Check for power to the pump assembly and check to make sure that the vanes on the drain pump are not broken. Read More... Safety note: testing, adjusting or bypassing anything while the appliance has power is a job for a qualified technician. Unplug it before you open it up, and keep it unplugged until every panel is back on.
Raymond February 08, 2013 for Model Number WTW6500WW1 My wife was doing laundry and the piece that locks the lid broke off and I am looking for the exact part to replace it. Thank you.
1 Answer Hello Raymond, The part that locks the door would be the latch assembly WPW10619844. Read More...
Raymond February 08, 2013 for Model Number Whirlpool Cabrio My wife was doing laundry and the piece that locks the lid broke off and I am looking for the exact part to replace it. Thank you.
1 Answer Hello Raymond, To properly assist you we will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Dan D January 10, 2013 for Model Number 110.27092601 I opened the lid lock switch (p/n W10059230) to free up the slide mechanism and it dropped the 2 metal slides. I need an exploded view to see how the slides are reassembled in the switch. Can you help?
1 Answer Hello Dan, Unfortunately we would not have a picture or diagram to show you how the internal look is of the switch. Read More...
Mike V. October 22, 2012 for Model Number MTW6600TBO How do you access the connection for the lid lock replacement?
1 Answer Hi. Tape the lid shut on both sides so when it is lifted it will not flop open and damage issues. Use a putty knife on the top of the front panel corner approx. 6-1/2" inwards from the outside edge of the washer. Push in the top lock and lift up on each corner. The lock is bolted on with 2 screws. Carefully route the new latch assy. where the side clips hold the latch part # WPW10619844 wires from the top of the tub from shorting. Thank You. Read More...
Angel September 02, 2012 for Model Number MVWB750WQ2 Hi, My Maytag MTC Bravos is not cycling it is giving me a 'lid' code whenever I chose a cycle, can you help me identify what is wrong?
1 Answer Hello Angel. Based on the error code, it sounds like the latch WPW10619844 is bad and will need to be replaced in the unit. Read More...
Tom L August 23, 2012 for Model Number 110.27082602 I constently get the error code UL everytime I try to use my washer. I know it stands for unbalanced load but it never corrects itself. Always have to take everything out and realligne the load. Have to do this several times and it usually still doesn't work. Very agervating to say the least. Takes forever to dry the close when they dont spin out properally. How do I fix this problem?
1 Answer Hello Tom. Based on the information you provided, it sounds like the suspension W10820048 is bad and needs to be replaced on the unit. Read More...