Richard August 01, 2012 for Model Number W10059230 Hi, I have removed my lid locking mechanism from my Whirlpool washer. My part is now defective because the latch that extends (to one of 3 positions) has snapped because it has weak point that appear to be designed to break. There is no way in hell I'm going to pay $50 bucks to get a replacement part because this part is "patent pending", and appears designed to fail. This combination means that the patent owner can make money every time this part breaks. I also wouldn't be surprised if the government mandated that a complicated hard-to-defeat switch like this be used. That way they can guarantee that the lid will never be open while the agitator is moving or the basin is spinning. I am tire of the "think of the children", lets "design this so we can't get sued" BS. The bottom line is that I'm forced by lawyers and/or government to pay for safety that I don't want. LAME. I want to bypass this switch or fool the computer into thinking that it is operating normally. Has anyone successfully done this? If not, I am going to take this part into work and have it examined by our electrical engineers. It appears that there is a resistor or diode in this device that you cannot bypass with a simple short because the computer detects that and refuses to cooperate.
1 Answer Hello Richard, If the lid assembly WPW10619844 broke, the only fix it to replace it. As far as being designed to break goes, you will need to address this issue with the manufacturer. Read More...
Donald June 22, 2012 for Model Number wtw6340ww0 whirlpool cabrio Washing machine works through all cycles except when it gets to spin cycle.
1 Answer Hi Donald. Does the lid switch lock ? Part # WPW10619844. It will not allow spin for safety if the lid is not locked. Is the cold water filling the basket at the start of the rinse cycle? Water valve part # W10364988. It will be advantageous to find the supplied tech sheet inside the cabinet to aid you in the diagnosis. It allows you to put the unit in a diagnostic mode which brings up fault codes and tells you which circuit needs assistance. What is the fault codes showing? Thank You. Read More...
Jenn June 07, 2012 for Model Number 11027072604 I got a DL error on my washer. I have check to make sure everything is secure. Will replacing the latch switch fix this problem?
1 Answer Hello Jenn. If the latch assembly is not working on the washer, you will need to replace the door latch WPW10619844. Read More...
Ray May 17, 2012 for Model Number ap3891130 Is it possible to disenable lock lid switch as this seems to be a recurring problem? (plastic switch/housing.
1 Answer Hello Ray. No, there is no way of bypassing the latch WPW10619844. If it is bad, you will need to replace the latch. Read More...
Mary A. March 07, 2012 for Model Number mvwb750wro We are trying to replace the latch (lock).But can't get the cabinet top off. How do I get it off?
1 Answer Hello Mary. There are two clips WP8563785 under the front corners of the top panel. You will release these clips and raise the top of the washer to access and replace the latch WPW10619844. You can use a flat blade putty or butter knife to release the clips. You will also need to remove the control panel off the unit to run the wires for the latch assembly to the control board and install it. Hope this helps. Read More...
Tim December 30, 2011 for Model Number wtw6200sw0 I am getting error code "du". I have to unplug washer to eliminate the locking mechanism to stop clicking. Will replacing the latch solve this issue? The washer still works, I just have to hit cancel- start, and it works fine.
1 Answer Tim, Before you replace the lid lock switch assembly, check and make sure you have no loose wires or connections at the lock assembly, check the lid assembly for loose fit, proper alignment, etc. First, Then replace the latch switch assembly. Good Luck and Thanks Read More...
Darwin December 26, 2011 for Model Number WTW7800XW0 Got as far as ready to remove the lid lock harness. How in the world does one get the end connector snaked back through the console hole? Plus can you send me a schematic of the P12 pin numbers?
1 Answer Hi Darwin. There is a narrow plate at the back of the cabinet area. It is on the upper RT. Side as you are facing the front of the unit. It covers the electrical wires and the pressure switch hose as they pass from the console to the tub areas. It is a very tight squeeze but it can be done. Make sure that you do properly lay all together so they do not pinch or restrict air flow (in the tube). The lid latch is part # WPW10619844. There is a supplied wiring diagram behind the control panel or is a tech. sheet inside the cabinet towards the front. Thank You. Read More...
Jayson O December 26, 2011 for Model Number not sure I have a Cabrio washer and i am getting a du fault code, will replacing this part solve the problem?
1 Answer Hello Jayson. Yes, based on the error code you provided, it sounds like the latch assembly WPW10619844 is bad and will need to be replaced. Hope this helps. Read More...
Casandra F. December 13, 2011 for Model Number wtw66005132 I was wondering if there was a detailed schematic of part #ap3891130 ?
1 Answer Hi Casandra. Check the lid lock motor winding and switches by removing P12 from the machine/motor control, and checking the resistance values shown in the following Lid Lock Resistance table. Motor Winding locked or unlocked 35 ±5 O P12-2 P12-3. Lock Switch -Home 0 O Open Circuit P12-4. Lock Switch -Lock ,Open Circuit (unlocked) 0 O (locked) P12-1 P12-7. Lock Switch - Lid. Lid Closed = 0 O. Lid Open = Open Circuit Contacts Measured P12-5. Thank You. Read More...
Ken October 07, 2011 How do I lift/open safely the top of my whirlpool Cabrio washer? I am replacing the door latch which broke
1 Answer Hello Ken. There are two clips under the top panel in the corners. You will use a flat blade putty or butter knife and press in on the clips. They can be tight sometimes. Once released, the top will raise up on the washer. Use a board to put under the top assembly to brace it from falling on you while your replacing the latch WPW10619844. Hope this helps. Read More...