J. Jennings August 17, 2015 for Model Number HDE5500AYW Serial #72499295je. My question is almost the same as the gas dryer question but my dryer is electric and my model # starts with hde. Original code is #8 (sticking button?) and later only 00 will show. Chirping, nonresponsive buttons when pushed; intermittently works and not works. Console is sealed but once taken off dryer and then replaced; it m-i-g-h-t work until it happens all over again. I would like to make my console operate normally without replacing it if possible but if not, what part should I get? Also, what is difference between hde and mde?
1 Answer J. Jennings, The model that you would have would be a MDE5500AYW as there was not a HDE model manufactured. As for the issue with your unit, You will need to replace the console as it is not able to repair these consoles. Read More...
Wendi April 22, 2015 for Model Number MDG5500AWW Maytag Neptune Gas Dryer, serial # 69916349GG Which control panel is needed? My dryer was beeping randomly, now there are lights on but I cannot get it to start or it may start once in a while if you are lucky.
1 Answer Wendi, The console for your unit based on the serial number is 22004444 which will most likely be the cause for the failure. Read More...
Nicole April 13, 2015 for Model Number MDE5500AYW Hello, I have an electric maytag neptune dyer which is beeping like crazy! It first started with beeping; now it is beeping and the buttons arent responding like they should. I'm not sure what part I should go with? Im seeing 2 different Led Console Assy that are compatible with my model ( I think!). The model number is MDE5500AYW and the serial number is 72498876JE. Thank you so much for your time and assistance! Nicole
1 Answer Nicole, The part number for the console that you would need is 22004444 and the beeping would be caused by a stuck key. Read More...
Ray February 02, 2015 for Model Number MDE5500AYW I have a MDE55OOAYW Serial # of 40434123ZS....I need the entire consol...board as well ...is the "Assembly" you offer a complete unit? and which of the 2 offerings do I go with? Along with somewhat bad capacitors, I need the "BAND'" which communicates from the Timer sensor on the front to the board... Its built in...thus I need an entire consol... board included....am I on the right path?
1 Answer Ray, You'll need the 33002536 LED Console Assembly would be the part to order for the model and serial number you supplied. It will have the "ribbon" and all the parts needed to transfer the part and install it on your dryer. Read More...
Laurie J November 02, 2014 for Model Number MDG5500AWW Additional info from previous question - The dryer will not turn on at all now. Some lights and sounds still work, but the intermittent problem is now always a problem.
1 Answer Hello Laurie. If the control panel has come buttons that work and others that do not, you will need to order and replace the control panel on the unit. Read More...
Laurie J November 01, 2014 for Model Number Maytag Neptune MDG5500AWW s/n: 71000174GX I have read through all previous questions. Apparently, I need a new LED Panel - My dryer's panel lights on left are on, those on right are not and dryer will not start. We wait 15 minutes, go press start, and it starts. Problem is intermittent. It's not thermal related, as I tried turning it on first thing this morning - same thing, it didn't start. I went in 20 minutes later, pushed start and it worked. Which part should I order? Thank you!
1 Answer Laurie, You're pretty much on target, you'll need to replace the console assembly 22004444 (based on the model and serial number you supplied). The key pad circuits have started to deteriorate and will eventually affect all the key pads. Read More...
Henry Lutz September 06, 2014 for Model Number MDG5500AWW Which control panel is the correct one for my dryer? The serial number is 66941130EL
1 Answer Henry, The correct console for your model dryer with a serial starting prefix of 66 would be part number 33002536. Read More...
Gerry August 06, 2014 for Model Number MDG5500AWW Hello, Two control panels are indicated in the parts list. 22004444 (AP4029362) and 33002536 (AP4043476). How can I determine which I need to use? Thanks, Gerry
1 Answer Gerry, it would depend on the serial number of the dryer. Please obtain this information and repost for further assistance. Thanks. Read More...
Eli July 12, 2014 for Model Number MDG5500AWW I replaced the Control Panel on my Maytag Neptune Dryer MDG5500AWW because the person who came to see it told me the part needed to be replaced. So I bought the part and installed it myself. So I plug it in and turn it on to try it, and it did turn on and started to dry perfectly when suddenly after a short minute it turned off completely so I tried it again and exactly the same thing happened. There's no funny noises or codes showing up. So now I decided to stop and research myself before calling the technician again.
1 Answer Hello Eli, Pull the tech sheet and follow the instruction on there for the diagnostic mode. This should give you the fault codes in there and point you to the area to look for the issue. If the unit will not go into the diagnostic mode, the control is assumed to be at fault. Read More...
Renalta July 12, 2014 for Model Number MDG5500AWW, serial Number 69987518GC My Maytag Dryer does not start. The LED lights turn on from the left to right and keeps repeating. The panel does not respond to Air Fluff and Time (+) key to enter the service mode. I have unplugged and re plugged, happens the same thing.
1 Answer Renalta, The issue with your unit sounds like either a stuck keypad or that the unit is in a demo mode. To remove from demo mode try pressing and holding the Air fluff and Sensor button. Read More...