Patty January 02, 2014 for Model Number 790.75761001 I need help locating the oven temperature sensor on my range
1 Answer Patty, Based on the model number you supplied, the correct oven temperature sensor for your range is 5304497424 / [316134900].On this style range the sensor is located in the left lower corner of the back wall of the oven cavity. To replace the sensor you'll need to move the range away from the wall 1. Disconnect electrical power from the range. 2. Unplug the oven sensor. 3. Remove the two screws holding the sensor to the back of the range. Reverse the procedure and check the oven for operation and any error codes in the display. Read More...
Yisroel January 01, 2014 for Model Number Electrolux I have an electrolux oven, and I started getting error F4 whenever I turn it on, and the door fan automatically turns even when the oven is set to off. the resistance of the sensor is 500 ohms at room temperature, is that for sure a sign that its bad and needs replacing. I saw online that it should be 1000 ohms, but is this true for all make and types of sensors? Thank you
1 Answer Hello Yisroel. The oven temp sensor should read 1100 ohms at room temp. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Vernon December 23, 2013 for Model Number mes5775bab The oven gets to hot and burns things often. I just checked the temp with a digital temp prob it shut off at 455 deg cooled down to 420 deg then back on and up to 450 deg. the controls were set at 400 deg. Will the long temperature probe fix this problem?
1 Answer Vernon, You can test the oven sensor to see if it is faulty. The oven sensor should ohm out at 1090 ohms and if not then the sensor is bad and would need to be replaced. Read More...
Randy December 12, 2013 for Model Number MER6755AAQ Greetings, I have a range MER6755AAQ that has two ovens. The top oven is causing problems, the bottom oven works fine. When a temperature is selected and the oven turned on, the oven will reach that temperature then fail to maintain it. The bottom element will not get hot enough to keep it going at 350. The oven will slowly decline in temp and will be lucky to keep it at 200 degrees. . Sometimes the broiler element will glow for a minute or two, then it quits on it's own. Any ideas?
1 Answer Hello Randy. Either the lower element is bad or the control board needs to be replaced. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Mike December 01, 2013 for Model Number Norge BNEW3H9TZ-EV Hi, I think I need to replace my oven temp sensor (F2 code) but on the Norge BNEW3H9TZ-EV, it appears to be fastened inside the oven with the wiring fed through the body and insulation out to the rears of the oven. Is there a handy trick to feeding the new sensor wiring, as it isn't a straight line? Or would it be easier to make new holes as attach from the rear? Thanks!
1 Answer Hello Mike. You will remove the back panel 3801F031-51 off of the unit to access and replace the sensor. Read More...
Romy November 25, 2013 for Model Number Magic Chef # 38 HA-36TX The buzzer came on even not doing anything on it. It shows an F1 code. you got to unplug it and it will stop buzzing and the code disappear and it appear again and again now the oven is not working any more. What do you think is the problem?
1 Answer Hello Romy. Based on the error code you provided, the control board is bad and will need to be replaced on the unit. Read More...
Kenny November 23, 2013 for Model Number jenn air range model sve-47500 I purchased a replacement oven temperature sensor. The end connection is different and adapters to not fit into wiring to brains of oven. Do you all have different adapters or what else can I do?
1 Answer Hello Kenny, You will need to order two ceramic wire nuts DE81-08428A. Cut the connector off and use the ceramic wire nuts to connect the two wires. Since this is not a polarized part the wires can be crossed with no ill effects. Read More...
Ernie November 19, 2013 for Model Number LER3330AAZ The oven does not heat at all. I removed the element and checked it with an ohm meter and it shows continuity. Could it be the oven temperature sensor?
1 Answer Hello Ernie. No, if the element is good, you will need to replace the control 5701M760-60 in the unit. Read More...
Rosanne November 08, 2013 for Model Number MER6770AB I have a double oven and I get trouble code F9-3. I checked both oven sensors the top one has a resistance reading of 1052 and the bottom one reads 1074 both at room temp. When I would cook in either oven after a few minutes at 350 degrees the oven goes in the fault code with above fault. What would be my next step?
1 Answer Hello Rosanne. Lock and Unlock Switch UpperOven. Check switches and wiringto latch assembly. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Cathy October 23, 2013 for Model Number GFE461LVS0 my oven will say the temp is 350 but will only be maybe 200. I bought a thermometer to test it it will finally reach 350 but then it may go up to 400 after that is this the temp control?
1 Answer Cathy, The oven temperature sensor needs to be tested or replaced, as the first option for a range with erratic temperatures. Especially after a self clean cycle, or an older range. The sensor resistance can become erratic. But first, pre heat the oven 15 to 20 minutes, then allow the oven element to cycle off an on three or four times, then average the oven temperature for the three or four cycles. If need be you can re calibrate the control by +/- 25 degrees, if needed. Read More...