Bob October 10, 2013 for Model Number Maytag Oven Model # MGR6772BDB This double oven stops working when baking ..both upper and lower ..it flashes F1-2 and beeps. Only way to clear is to unplug unit and start over. This happens not on a regular basis ... but seems to be getting worse. Sometimes it also just shuts off heating even though the temp on the panel still shows cooking temp...like 350 degrees. Only way to tell then is to have the oven light on ..and it will go off if it shuts off. I have read all the Questions and Answers to date ...so I think it is the lower oven sensor....if that doesn't work then I assume it is the oven Control unit.. Is this correct?
1 Answer Hello Bob. Lower Oven >650°F with door unlocked. Check actual upper oven temperature,if > 650°F check sensor.Check actual lower oven temperature,if > 650°F check sensor.Check actual upper oven temperature,if > 950°F check sensor.Check actual lower oven temperature,if > 950°F check sensor.Check membrane switch for connection or damage.Check upper sensor, harness, and connectionsCheck upper sensor, harness, and connectionsYou can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Martha September 29, 2013 for Model Number maytag smooth top range Model MER5775qab I set digital temp to 350 but oven does not heat beyond 100-120. The broiler works fine. Is this oven temp sensor or element?
1 Answer Hello Martha. Test the elements in the unit and make sure there is 240 volts coming to them. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Terry September 01, 2013 for Model Number cwe5800ace This is a double wall oven. My top oven will not heat up. When you push the control button for oven temp it reads 350 then starts at 75 but nothing happens, it won't heat up. Would it be the sensor or the control board. This is a touch control panel.
1 Answer Terry, Did you check the bake element WPY04000066 for a "closed" circuit and that the wires aren't loose or damaged ? and are you sure you have 220-240 VAC to the wall oven(easiest way to check, does the broil element come on in the broil selection) The sensor 12001656 would normally cause an F2 or F3 error code in the display. If all's OK, you're most likely going to need the ERC 7601M285-60. Read More...
Mar August 12, 2013 for Model Number MER5875QCF The oven temperature is not accurate and constant. Do I need to replace the oven temperature sensor?
1 Answer Mar, You could test the oven sensor. The sensor should have a resistance reading of 1090 ohms at room temperature. Read More...
Tim July 29, 2013 for Model Number Whirlpool Super Capacity 465 Electric Range My oven does not stop at the selected temperature and continue to heat up the oven until I turn it off. Could this be a malfunction oven temperature sensor? Will replacing the sensor solve the problem? All the stove elements works properly.
1 Answer Hello Tim. Most likely, the board is bad and not the sensor. Check the sensor and see if it changes in resistance when the temp changes. If so, the sensor is good and the board is bad. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Nancy B. July 17, 2013 for Model Number MEW5527DDB My Maytag wall oven MEW5527DDB, will not cook. The temp seems to reach the designated temp them after a few minutes the temp display disappears and the Bake light is flashing. The oven temp has dropped way down to maybe 110 degrees. I'm thinking it could be the Oven Temp Sensor Part # 12001656, or the computer board. Can you help me?
1 Answer Hello Nancy, The temperature sensor (AP4009009) should read about 1100 ohms of resistance at room temperature. This reading can be taken from the terminal on the clock to test the wiring also. If an incorrect reading is given, retest the sensor at the sensor connection to the harness. If the reading is still wrong, change the sensor. If it tests good from the control connection, the sensor and the wiring are fine and the board (AP4097448) will be the issue. Read More...
Pat July 16, 2013 for Model Number 38HA-6TVW 38HA-6TVW Electric oven. Broiler and self clean will not work. Set the temperature for bake or broil, the oven starts to pre-heat then about 30 to 60 seconds, the oven turns off. The same with the self clean. Could this be a sensor rather than a bad control board?
1 Answer Hello Pat, This is most likely a bad clock. The part number will be determined by the series number, (usually determined by the serial number), on the I.D. tag. If there are no fault codes, it is most likely nothing to do with the temperature sensor but since this clock senses the voltage going out and the voltage coming back in, there could be a bad element or a wiring issue so they should all be checked before ordering the clock, but the clock is the most likely cause. Read More...
Geoff July 11, 2013 for Model Number mer6769baw Lower element in lower oven does not heat up. It has been replaced.
1 Answer Hello Geoff. If the part is new, and it does not heat up, you will need to order and replace the control board in the unit. Read More...
Pamaytagrepair June 24, 2013 for Model Number MER6772BAQ On the diagram "05-Oven parts for Maytag MER6772BAQ" it shows item 7. This item 7 has two entries in the list below. The first is "Oven Temperature Sensor Kit" AP4009009, the second is "Oven Sensor" AP4099532. Is one of these for the upper oven and the other for the lower oven? If so, which goes with which oven?
1 Answer Hello! Oven sensor part number WP7430P044-60 is the oven sensor for the upper oven and part number 12001656 is the oven sensor for the lower oven. Thanks! Read More...
Gary June 16, 2013 for Model Number mer5570aaw Panel reads LOCK but oven door is not locked and will not cancel or take any input. Can not use oven,set clock or anything else that requires instruction. Was trying to set oven to self clean when this problem happened.
1 Answer Gary, Based on the information you will want to access the latch assembly to make sure that the switches are good. If the switches on the latch assembly checks ok then you will need to replace the control board. Read More...