Will November 07, 2016 for Model Number 911 I have a Kenmore double wall oven (electric) that the temp sensors have both gone bad. 911 seems to be the only model number, followed by41369690. I can't find the right sensors. Can you help?
1 Answer Will, The part number for the oven sensor for your unit will be WB21X5301 which you will need one for each of the ovens if both are bad. Read More...
Ray November 02, 2016 for Model Number CWE5800ACB; sERIAL #21274424EL Is there any trick to replace this part in a double wall oven for the upper oven without removing the oven from the wall?
1 Answer Hello Ray. If you can see the screws inside the oven, then you can replace it from in there. If you can not see the screws, you will have to pull the unit out from the wall to replace it. Read More...
Ray November 01, 2016 for Model Number CWE5800ACB Symptoms: 1)Upper oven control panel lights and shows no error codes. All seems normal until temp is set. 2) In the upper oven, when setting for 350 it jumps down to 75. 3) Neither the broiler or lower element of the upper oven light. 4) Lower oven heats and works fine EXCEPT the red light is not going on and off when the temperature is cycling. Research seems to point to oven sensor, but part indicates it is for a Whirlpool stand alone oven. Can you figure out from the wiring diagram what is common to the lower and upper oven? Can one part explain both problems?
1 Answer Ray, You could test the oven sensor which should have a resistance of 1090 ohms of resistance. If the resistance checks ok then this would be a control board issue. This is what the issue sounds like it would be. The part number for the board is WPW10201915. Read More...
Craig October 03, 2016 for Model Number MEW5627DDW17 My in wall double oven turns on but will not heat. All other functions on the digital display work. The display says 100degrees but there is no heat. This happens in both ovens. I bought this new 3 years ago from Sears and I'm surprised it has failed so soon. Any ideas?
1 Answer Craig, With both the upper and lower oven not heating it would be recommended to test to make sure that proper power is coming to the unit. If this checks ok then the issue will most likely be caused by a faulty control board which is part number W10757360. Read More...
Linda September 04, 2016 for Model Number n9457x5 My oven won't shut down. I had to flip the breaker.
1 Answer Hello Linda, This is most likely a stuck relay on the relay board 4338554. I'm sorry but this part has been discontinued by the manufacturer and no satisfactory substitutions have been provided. Read More...
Ivan August 04, 2016 for Model Number MEW5527BAW I just bought a used maytag electric oven MEW5527BAW and it was a little dirt from the inside, so i scrub it with losts of multipurpouse cleaner and water to rinse it and in let it dry for 3 or 4 days, now that i installed does not want to heat when i set it to bake or broil, the panel works fine, maybe its the oven sensor, dont you think?, thanks a lot for your answer
1 Answer Hello Ivan. You will need to check the element, sensor, and control board on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Bobmc July 29, 2016 for Model Number cgr3510adh will a oven sensor with a long tube work in an oven that has a sensor with a short tube?
Chuck M. May 24, 2016 for Model Number WW27210B Upper (convection) oven does not heat up. Can set convect bake temperature on display panel, but then actual oven temp indicates 100 degrees and does not increase...clock and other settings work fine, and lower (regular) oven also works fine. Is problem ether a bad thermostat in upper oven or perhaps the temperature sensor?
1 Answer Hello Chuck. Make sure the element is good. If so, the board 12001690 is bad on the unit if the thermostat WP71001844 is good. Read More...
Brian April 19, 2016 for Model Number ??? Our oven is at least 35 years old, the metal plate to get model number is gone. It is a Whirlpool Continuous-Clean wall oven. The oven thermometer prob needs replaced. Is there a part available for this anymore?
1 Answer Brian, While a lot of the parts for a unit this age would be discontinued, we would not be able to determine if the oven thermometer probe is available without the model number of the unit. Read More...
David W February 10, 2016 I have the 2013 year whirlpool gas range, Cannot find the model no but, the oven sensor shows open with an ohm meter. the sensor number is W10181986 can you mat hit.
1 Answer David, If the oven sensor is showing open then you will want to replace the oven sensor on the unit. Read More...