Len December 29, 2011 for Model Number wgd9600tw1 How far down do I screw regulator on to spring ? I screwed it down snug and it seems to sound like a jet . I saw on youtube on furnace you should use a meter ? They said to start with 3 full turns ? Is this the same, or am I over thinking this whole thing?
1 Answer Hello Len. Make sure the regulator WP694423 is set for the proper gas and you will screw it all the way down. Hope this helps. Read More...
J. R. A December 28, 2011 for Model Number 110.87683110 I am converting this from LP to Natural Gas. I replaced teh regulator screw. What is the initial setting for the screw. How do I know if it is set in the correct location?
1 Answer JRA, There are four(4) parts involved in converting the gas valve back to Nat Gas, spring WP694422 regulatorWP694423 capWP694424 and orificeWP234868, all the LP Gas parts will need to be removed and replaced with the NAT Gas parts for the unit to operate safely and properly. There are no adjustments to make, other than the air shutter on the burner. All the fittings need to be snug and tight, and checked for gas leaks with soapy water. Thanks and Good Luck Read More...
Norma L. September 04, 2011 for Model Number dg210 We recently purchased an igniter , and themal coils, installed these. The problem still exists, the originsal problem being, it turns on, flame comes on, then it turns , the flame turns off, that had been the problem all along
1 Answer Hi Norma. There is a flame sensor that is directly to the left of the ignitor. It is always normally closed but will open the circuit as the flame reaches temperature. This part # is WP338906. The high limit switch will shut off as a safety also. This part # is WP338906. Please let us know if we can further assist you. Thank you. Read More...
Michael S. August 19, 2011 for Model Number LGR4634EQO I have a whirlpool lp gas dryer model # LGR4634EQO. What parts do I need to convert back to Nat. gas ? Thank You Mike.
1 Answer Hello Michael. You will need to order the orifice WP234826, the regulator WP694423, the spring WP694422, and the limiter WP694424. Hope this helps. Read More...
Nate August 15, 2011 for Model Number LGR4634EQ3 Hi. I recently bought a whirlpool dryer that was converted to LPG. However the original parts were lost. I need to order the parts to convert from LPG back to NG. Which parts do I need and do they come with instructions?
1 Answer Hello Nate! You will need to order the natural gas orifice WP234826 and leak limiter WP694424. These parts do not come with any instructions. You can visit our free repair forum for installation assistance, here is the link. Thanks. http://forum.appliancepartspros.com/register.php Read More...
John July 10, 2011 for Model Number Wgd9400sw2 Do you need to replace the regulator and spring when converting from lp back to nat gas. Looks like the original conversion to lp required only the change in orifice and leak limiter.
1 Answer John, You normally don't need any parts to convert back to Nat.gas, unless,you've lost the parts. But you are basically correct, replace the burner orifice WP15418, and "flip" the regulator limiter cap. over and reinstall the cap. Thanks and Good Luck. Read More...
Eric February 20, 2011 I have a whirlpool mod:LGR4634JQ2. It is currently set up for LP. What do I need to buy to convert it back to natural gas. Thankyou, Eric
1 Answer Hi Eric, to convert back to natural gas you will need 1 of each: WP694424, WP694423, WP694422 and WP234826. Hope this helps! Read More...