Jesus February 17, 2015 for Model Number MDE9520AYQ Hello, I have a Maytag dryer. We are only able to dry cloths on the "More Dry" setting and it's extremely hot. We cannot dry the cloths on any of the other settings. The day before yesterday it stopped heating. Do you have any ideas about what could be? Thank you.
1 Answer Jesus, This issue would most likely be caused by a faulty cycling thermostat. The part number for the thermostat is WP307249. Read More...
Pat September 19, 2014 for Model Number MDG7658AWW Dryer heats but timer doesn't advance in any setting. Nothing lights up in auto dry setting. Timer has been replaced and venting has been cleaned.
1 Answer Pat, The timer motor will route through the dryness control and if it is faulty the timer will not advance in any cycle. The part number for the dryness control is WP33002389. Read More...
Kaivon April 17, 2014 for Model Number Maytag Atlantis gas dryer mdg 8400aww My gas dryer runs and gets hot but does not shut off unless you open the door and timer does not advance at all in any setting. Moisture sensor light also stays blue and never turns to orange/red even though cloths are totally dry. I have checked the vent and its clear - even disconnected the vent hose to make sure no obstructions and ran the dryer and still the timer would not advance in any setting, moisture sensor stayed blue in all settings, and the bit never shuts off unless you open the door. Is it the moisture sensor. timer or other part? The unit is about 6 years old.
1 Answer Kalvon, First remove and check the wires to the sensor bar 33001809 then clean the sensor bar with rubbing alcohol and the surrounding area. Lower the control panel and check the dryness sensor control board for damaged or burnt components on the board WP33002734 (depending on serial number). Read More...
Terry March 11, 2014 for Model Number maytag mce8000ayw dryer The bottom dryer will only dry for a short time and then it shuts off for a few minutes then comes back on for a few minutes and then finally just shuts off completely. It heats up ok and sometimes it will run completly through a cycle with no problems. I cleaned out the vent and even installed new vent hose. I also took apart the front of the dryer and cleaned out everything which had never been done since it was new. It was a mess.
1 Answer Hello Terry. Based on the information you provided, it sounds like the motor may be overheating in the unit. If the motor is overheating, you will need to look for something binding the drum in the unit. If the drum is not binding and the motor is overheating, you will need to order and replace the motor in the unit. Read More...
Stan R. March 10, 2014 for Model Number MDE7600AYW My dryer is not heating and I only have 120 volts to the element. The continuity seems to check ok on the thermal fuses and the high Limit sensor. I'm at a loss as to what could be wrong.
1 Answer Stan, you'll need to check the motor WP33002795, timer WP33001932, and thermostat part number WP3387137 which is located on the blower housing. Hope this helps you, thanks. Read More...
Davis February 28, 2014 for Model Number MDE7400 AYW When try to dry a load of clothes I can only dry on 20 minute or on less dry, I replaced the timer and dryness control, cleaned off sensor, still will not dry from any timer setting in the intellidry mode. Timer is only 6 months old. I have not replaced the sensor or the chime switch. The heating element works fine. Any idea.
1 Answer Hello Davis. If the timer worked for 6 moths and then messed up, the timer is bad on the unit. You will need another timer if that is the case. Read More...
Greg November 13, 2013 for Model Number MDE6800AYQ My wife is saying the the cloths will not dry when using sensor dry. They run the 50-60 minute cycle yet are still damp. When run on timer for 50-60 minutes they are dry. I've not experienced this myself yet. The last time I ran the dryer, a few days ago, I went back a couple hours later and found the cloths damp, but learned that she had turned the dryer off when she ran out for an errand and forgot to turn it back on when she returned. The the duct seems to be clear and the sensor appears to be clean but I've heard that dryer sheets can coat sensor and make them not work.
1 Answer Hello Greg. Yes, the sheets can coat the sensor bars. You can use rubbing alcohol to clean the bars in the unit. Read More...
Steve September 19, 2013 I have a Neptune dryer front load when you close the door and push the start button it won't do anything but beep and the time dry buttons do not work. What could it be? I need help, friends.
1 Answer Hello Steve, You need to check the door switch, the push to start switch, the drive motor, the thermal fuse and the timer. These and the wiring harness are the components in the circuit that could cause the issue. If you look in the control panel, you should find a copy of the tech sheet. Sometimes this will be in the bottom of the cabinet. Let us know if we can assist further. Read More...
Steve August 09, 2013 for Model Number MDE7657BYW My dryer is not shutting off or even registering the clothes are dry when using the sensor settings. Am having to use the timed dry. Could it be that the sensor bar needs to be replaced?
1 Answer Hello Steve, You need to check the exhaust duct and clear the restriction. If the timed dry works, the only thing that will prevent the auto dry cycles from working properly is a lack of air flow. I get lots of arguments about this but think of it like this: When the hot moist air cannot exit the unit, the sensors continue to sense the same moisture and the timer never advances. If you want to test this, remove the exhaust duct from the back of the dryer and start it on an auto dry cycle. You will see the timer advance within 5 to 10 minutes. If the sensor bars were bad, the timer would advance all the time because it would never see the moisture and the timer would cycle without ever stopping. Read More...
Bailey August 04, 2012 for Model Number MDE3000AYW Maytag electric dryer How do I check the sensore bar? Should there be continuity between the two connection terminals when the dryer is cold? My dryer will not start when I push the start button. I have checked the door switch, the thermal fuse and the heater element. All three have continuity. There is continuity across the start button when pushed in. What else should I check next? Thank you.
1 Answer Hello Bailey. You place a wet wash cloth across the bars and they read closed for continuity. If all of those parts are good, then it sounds like the motor is bad or the wiring on the unit. Read More...