James W. July 17, 2012 for Model Number mde88000ayw Even though I set my control to "delacate air fluff" the temperature doesn't drop from high. What's going on?
1 Answer Hello James, There are only two possibilities and it could be a combination of the two. You see, when air fluff is chosen, you break 120Vac off of the heater element. If the exhaust duct is restricted, heat will be held in the unit and appear to be still heating because the heat is blown past the felt dryer drum seals back into the cabinet where it is recirculated. The other possibility is a heating element WPY308612 shorted to ground, causing a medium heat situation anytime the unit is running. While this is possible, it isn't likely because, as I said, this would be a medium heat situation. Since the heating element is designed to run on 240Vac, and if it's shorted to ground it will only have 120Vac on it, it would appear to be on low or medium heat at all times.....unless the exhaust duct is crimped or clogged. Check the exhaust for crimps or clogs as this is the most probable cause and the most denied by customers. Remember the duct should be as short and straight as possible while being a full 4 inches for proper air flow. Read More...
Hilo July 16, 2012 for Model Number MDE5500AYW My Neptune dryer works fine on timed dry but on any automatic setting it turns off after 2 minutes. Can you help me determine whether the moisture sensor needs to be replaced?
1 Answer Hilo, A quick and easy check/repair : Unplug the power cord or remove power to the dryer. Open the dryer door using a 1/4 in socket or nut driver rmove the sensor bar mounting screws(2) and lift upi on the sensor bar assembly 33001809, make sure both wires are attached to the terminals, carefully disconnect the wires(don't let them fall back into the cabinet) and clean the bulkhead area and back side of the sensor with a solution of warm soapy water. Clean the top side of the sensor bar with rubbing alcohol, and reinstall the sensor. Put a small load of damp articles in the dryer and start the machine, if it runs longer than two(2) minutes, you'll be fine. Thanks Read More...
Bbmello July 13, 2012 for Model Number MCG80000AWW On Sensor Dry, the dryer shuts off before the clothes are dry. Thank you!
1 Answer Hello BBMello. Check the thermistor WP31001590 and make sure it is good. If so, It sounds like the venting system is clogged or kinked. You will need to check the vent and clean it out. Be sure and clean the vent pipe and the dryer air duct assembly. If the air flow is not good, the unit will retain moist air causing the clothes not to dry. Try running the unit with the vent unhooked from the back of the dryer and see if the dryer works properly. Read More...
Eric June 20, 2012 for Model Number MDG4000BWW My gas starts and has full flame for about two minutes. Then the gas is shut off and won't restart even though it cycles through the igniter warming and the gas firing. I have to turn the dryer off and wait for an extended period of time before the flame will ignite again, at which time the process repeats. I've checked the resistance on the gas coils and they appear to be correct.
1 Answer Hello Eric, This is going to be a bad gas valve WP306176 as long as the flame sensor WP338906 reads zero resistance when it's hot. Read More...
Ht March 29, 2012 for Model Number MDG5500AWW My dryer does NOT stop when the clothes are dry (sensor mode). Could this be my sensor bar? How can I check it? Also, I noticed that there are two blue wires on one end but NO green wire. Are there more than two wires for this bar? Thanks.
1 Answer Hi HT. Create a log in on our website and insert your model in in the start here home page. Then scroll down to the lt. side and bring up tumbler view # 6. Under the part # 11 it shows the part #10 green ground wire. Your serial # may have not included this part. No-there are only 2 wires that hook to one end of the sensor bar as the opposite end tabs are folded to hold the bars in the mount. Use a ohm meter part # MA-DM1 and unhook the wires. Then set your meter scale on R x 1 and then put the leads on each sensor bar terminal. If good then you will ohm approx. .01-0 ohms. The same as if the 2-leads were tested together to make sure the ohm meter batty. is good. You want a complete path (no opens) on these two terminals. Now check from the microprocessor control part # 33003028 J-2 connector pins 3 and 4 where the sensor bar blue leads connect. UN hook them there and also ohm the 2-wires with the bar connected. The resistance from the total wire lengths connected should raise just slightly higher to approx. .5 ohms. If not find which lead has the possible open or short. This is mainly not the case in my opinion but it can happen. If all this is correct then you need to change the main control board. Thank You. Read More...
Barb January 27, 2012 for Model Number mdg9606aww Our dryer, at times, keeps running and won't shut off, we're thinking its the sensor bar ?
1 Answer Hello Barb. It sounds like the venting system is clogged or kinked. You will need to check the vent and clean it out. Be sure and clean the vent pipe and the dryer air duct assembly. If the air flow is not good, the unit will retain moist air causing the clothes not to dry. Try running the unit with the vent unhooked from the back of the dryer and see if the dryer works properly. Hope this helps. Read More...
Keith November 30, 2011 for Model Number MDE3000AYW When I was disassembling my Maytag Neptune dryer, the blue wire to the moisture sensor came disconnected, but the green one is still on. There are several points on the sensor where I can reattach the blue wire. I just want to be sure I'm attaching it to the right connector. Can you tell me which one that is??
1 Answer Hello Keith. On the back of the sensor bar 33001809 there are two terminals. You will attach the wire to the spade terminal that does not have a wire on it. Hope this helps. Read More...
Shondon July 08, 2011 for Model Number MDE5500AYW I have to run my dryer several times on one load for my clothes to get completely dry.
1 Answer Hi Shondon. This means your dryer vent system is very clogged and probably getting ready to have a thermal fuse open. Please check that your vent hose is not clogged or kinked allowing the moist heat to back up into your cabinet. Make sure your outside vent hood/cap assembly is opening and closing properly. You should do this regularly 5 or 6x through out the year. Make sure your dryer vent length does not have any sags and normally is placed as so the moisture will normally drain outside. Hope this helps. Thank you. Read More...
David July 03, 2011 for Model Number Maytag Gar Dryer MDG7400AWQ The Igniter Glows, gas fires up for about 10 seconds then it goes off. The Igniter glows again and gas fires up for 10 seconds but after this second time gas does not fire up even though the igniter glows every few seconds. Once the dryer is turned off and turned back on same process continues.
1 Answer Hello David! It seems that the secondary coil has failed on your unit. It is suggested to replace both coils at the same time. Your coil kit is part number 279834. Thanks! Read More...
Joe June 23, 2011 for Model Number MDE3000AYW The sensor bar came loose inside my dryer and there is one green wire still showing. How many wires are there to be on the bar and how do I get to the other wires. Is the bar even needed if you use the time cycle?
1 Answer Hello Joe. There should be two blue wires and a ground wire. The sensor bar is not used in the timed dry cycle. Hope this helps. Read More...