Jackie December 03, 2012 for Model Number Ghw9250ml1 Washer keeps displaying f5 on front of washer.Called appliance pros they said it was water temp sensor.How would I get to that part to repair it?
1 Answer Hello Jackie, To access the water temperature sensor, unplug unit. Take the lower access panel off the front of the unit. On the lower front part of tub there is the heater. On the heater there is a black box with a wire connected to it. This is the sensor. You want to check the wiring to the heater and sensor to make sure that they are good. Also check the continuity of the heater to make sure that it is not defective. If you do not have continuity then the heater WPW10426377 is bad and would need to be replaced. If it checks good then you would need to replace the temperature sensor WPW10467289. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Julie November 27, 2012 for Model Number Whirlpool Duet Sport HT Washer Hi there, Since I purchased this washer about 5 years ago, it will only wash in hot water even when the front dial is turned to warm or cold water. The hook-ups are in properly; do you think this is a problem with the water temp sensor, or something else?
1 Answer Hello Julie. Test for power to the cold water valve. If there is power there, and no cold water, you will need to replace the water valve in the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More... Safety note: testing, adjusting or bypassing anything while the appliance has power is a job for a qualified technician. Unplug it before you open it up, and keep it unplugged until every panel is back on.
Anthony November 06, 2012 for Model Number WFW9150WW00 I am trying to find the water temp sensor on my whirlpool front loader washer mod WFW9150WW00. Can you help me?
1 Answer Hello Anthony! The water temp switch on your model WFW9150WW00 is part number W11417619. Thanks! Read More...
Nazdasmom September 18, 2012 for Model Number wfw9750ww01 I am looking for yhr location of the temperature sensor on my wirlpool duet stesm washer.
1 Answer Hello Nazdasmom. The water temperature switch WPW10467289 is located on the front of the bottom of the outer tub assembly. It is number 27 in the diagram. http://www.appliancepartspros.com/partsearch/model.aspx?model_id=5512212&diagram_id=29385299#d29385299 Read More...
Gabor May 03, 2012 for Model Number kenmore he2 110.46462500 I`ve had the error code f 24. Could that indicate something other than the Water Temperature Switch. It tested fine at 140 F.
1 Answer Hello Gabor. Check and make sure the heater, sensor, and wire connections are good. If so, and you still have the error code, you will need to replace the CCU WPW10525355. Read More...
Gary March 10, 2012 for Model Number 110.47511701 I'm trying to find where the water temperature switch is located on my Kenmore HE2Plus Washer.
1 Answer Gary, the NTC Water Temp Switch WPW10467289 is located on the back of the outer tub assembly. Hope this helps, thanks! Read More...
Carol May 31, 2011 for Model Number WFW8410SW01 I'm trying to find the water temperature sensor (part # AP3128829) in my Whirlpool Duet Sport washer, but I don't see it on the parts diagram. Where is it and how do i replace it? Thanks
1 Answer Hello Carol. The water temperature switch WPW10467289 is located on the front of the outer tub assembly. Here is a link to the diagram page. It is #24 on the diagram. Hope this helps. http://www.appliancepartspros.com/partsearch/model.aspx?model_id=5152502&diagram_id=28247835 Read More...