Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Shock Absorber by Whirlpool

Best Seller
Manufacturer Part
4.89 (64)
By: Whirlpool
Part Number: OEM18035502
Manufacturer Part Number: WP8182703

The Shock Absorber is an OEM part for Whirlpool washing machines. This component is essential for reducing vibrations and stabilizing the washer drum during operation, particularly during the spin cycle. It helps to absorb shocks and minimize excessive movement, ensuring the washing machine runs smoothly and quietly.

Note: The unit requires a quantity of 4. Package includes 1 only; order as needed.

Symptoms of a failing Shock Absorber include:

  • Excessive shaking or vibrating of the washing machine, especially during the spin cycle
  • Loud banging or thumping noises during operation
  • The washing machine moving or "walking" across the floor
  • Visible damage or wear to the shock absorber

Causes of a bad shock absorber can include wear and tear from regular use, heavy or unbalanced loads that put extra strain on the absorbers, or physical damage from impacts or mishandling.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

More
$45.30

IN STOCK
Ships Tomorrow Guaranteed
Add to Cart

Questions & Answers

For Whirlpool Shock Absorber (Part Number: OEM18035502)

2 Answers

Gina,

If you push down on the tub it should spring back up. If it does not then the shocks would most likely be the issue. Also you would want to replace all of them if 1 is bad.

Read More...

2 Answers

Hello Gina,
On a front load machine, normally if a spring is the issue, the tub will sit against the door boot and the door will not close correctly. A bad shock will just cause an out-of-balance condition upon spin. For a more accurate diagnosis, please post a new question that includes the model number from the units' I.D. tag. Thank you for your patience and understanding in this matter.

Read More...

1 Answer

Hello Paula. Some models only have 3 shocks and some models use 4. If your model only has 3, then you will only need to use 3 shock.

Read More...

1 Answer

Jimmy,

With the inner tub rubbing on the outer tub and there being a knocking noise, this issue would be a broken spider on the rear of the inner tub. This spider is the tub support and you would need to replace the inner tub WPW10269756.

Read More...
Dave Z for Model Number 110.45862400 (Kenmore front load washer)

Our washer has served us well over last 9 years and we would like it to keep serving us. Recently I noticed more banging during the spin cycle and for last month or so have had F11 error messages which we worked around by unplugging and using drain and spin to end cycle. I took top (but not back) off, pushed drum around. It seems to move around freely and feels undamped, especially at rear. Looking down from top, I do not see any visible leaking of shocks, but like I said, they do not seem to slow downward motion. Reading some of the other comments, I wonder if after almost a decade the shocks need replacing, and more to the point, if the shocks were allowing too great a vibration, would that lead to the F11 comm error, or do you think that is a completely unrelated issue? No leaks and drum seems to still be in good alignment. Would appreciate your advice.

1 Answer

Dave Z,

The shocks would definitely cause the banging around if they are bad. As for the F11 error code, this would only be caused by the shocks if wiring has come loose. Also check the drive system for worn or failed components.

Read More...
Mike for Model Number WFW9150WW00

This is for whirlpool WFW9150WW00. My washer shakes really hard, and moves out of place. Also there is play in the drum. One of the shock absorbers is leaking bad. So that needs replaced. Here is my problem. How many shocks does this model have? I only see 3 shocks when it looks like there should be 4 Also I need to replace the bearings. But I can't find a part number anywhere. Not even on the whirlpool site. I don't know what bearing or bearings to get.

1 Answer

Jeff,

Typically when there is a growling/roaring type noise in the spin cycle, this would be a bad bearing on the tub. The outer rear tub would need to be replaced and the part number is W10772618.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google