Brian January 13, 2014 for Model Number 11028322700 My Kenmore washer will fill with water and then get to the agitator cycle and stop working. It hums for a little bit, then stops humming. I can get it to work sometimes pushing the button to off and waiting awhile and then turning it back on and then rocking the tub around. I have replaced lid switch and control switch. I'm thinking it maybe something with the motor. Any ideas?
1 Answer Brian, With the motor humming it sounds like the contacts in the timer WP8546681 may be sticking causing the unit to think it is in spin and agitate at the same time. For this issue you would want to replace the timer for the unit. Read More...
Kevin January 11, 2014 for Model Number lsq9200kq0 My washer is not agitating properly. It only spins clockwise. I replaced the thrust washer kit, yet the problem remains. All the parts are in good working order. I'm wondering if the agitation of going back and forth has something to do with the motor switch.
Kevin January 11, 2014 for Model Number whirlpool washer lsq9200kq0 Hello, my machine is not agitating properly, I noticed it is not spinning back and forth, only spinning clockwise, I already replaced the thrust washer kit, yet I still have the problem! All the other parts seem to be in working order, the only thing that it might be is the motor switch (ps350913) is it possible, any other suggestions.
1 Answer Kevin, With the units agitator not rotating back and forth, the issue would most likely be bad agitator dogs. The part number that you would need is part 285811. Read More...
Nick August 25, 2013 for Model Number MTW5620TQ1 My washer is spilling water over the drum during the spin cycle on large and super large wash loads. It looks like it is skipping the drain high cycle before it starts spinning. It pauses for the cycle to take place but nothing happens. I have replaced the timer control because it was sticking in the wash cycle previously, I thought this would solve both issues. It did not. I am currently looking at replacing the pump, or the switch for the main drive motor. Please help.
1 Answer Hello Nick. Based on the information you provided, either the pump WP3363394 or the drain hose is kinked or clogged. Or the drain line behind the washer is bad. Read More...
Chris S. April 02, 2013 for Model Number WTW5100VQ0 Hello Appliance Pros. I have a Whirlpool washer wtw5100vq0. It is located in a rental unit I have. The machine is about 1.6 years old. Tenant complain that during cycle machine started a burning smell , and he shut it down to prevent fire. I researched , and decided to replace coupling since it has rubber part, and it made sense that more likely the coupling was torned off. I opened the machine, removed pump and motor but the coupling was in a very good condition. I put motor and pump back in place , put machine back together , and decide to do a wash . Water started to fill the tub, I did not want to fill the machine with water so I advanced switch to Spin cycle. The machine made a buzzing noise like a hum coming from a seized motor. No burning smell. I shut off cycle right away, and turned control switch to another type of wash, and put on spin cycle again. Pulled control switch to start, and the buzzing noise started again. Then I shut off machine. When I had the motor disconnected from the gear assembly , I turned manually the coupling, and the shaft was turning easily Do I have a bad motor switch, clutch, motor, or gear assembly? The agitator turns freely when turn it manually . Please let me know if I am doing something wrong trying to diagnose it , of what part more likely needs to be replaced. Thank you, Chris
1 Answer Hello Chris. Based on the information you provided, it sounds like the timer WP8572976 is bad and will need to be replaced on the unit. You can test the blue wire to the motor during agitate, and should have 120 volts. If you have it on the black/white as well, the timer is bad. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Jamie M. March 24, 2013 for Model Number Maytag washer mvw(:300vwl Maytag washer after each cycle, it will not spin. I can lift the lid and let it back down and it will start spinning. It happens at every spin cycle. It's only about 2 years old.
1 Answer Jamie, I've found model MVWC300VW1 (C instead of (: and 1 instead of L). You'll need to test and replace the lid switch WP8318084 if defective. Thanks. Read More...
Linda January 01, 2013 for Model Number 110.29822800 KENMORE WASHER The knob does not work properly, spins when it should wash etc. Any suggestions
1 Answer Hello Linda, The first thing you want to do is check the knob on the unit to make sure that it is not cracked and pointing the wrong direction. If this is ok then you would want to check the timer and to see if there is a reversed wire on the motor. Read More...
Steve October 19, 2012 for Model Number mvwc500vw-1 Washer is tripping breaker just before spin cycles.....do I need the whole motor or some other part may be shorting or causing a high voltage draw?
1 Answer Steve, There are several things you need to check, since the washer fills, washes and drains, you most likely have a voltage issue to the washer. First check to see there is nothing stuck between the tubs. Dismount the motor and pump assemblies from the transmission, turn the drive coupler on the input shaft in both directions, make sure there are no "stiff" areas or the gearcase doesn't lock up. Then you'll need to check the wiring between the water level switch and timer. If alls Ok, and the voltage is proper when the motor starts to spin, Then replace the timer WPW10111389. Read More...
Wayne August 09, 2012 for Model Number 11028322700 Washer fills up, then does nothing! Replaced the timer already, still no response! What else could it be? Took off part#3952056, saw slight burn mark on grey wire coming from the lid switch. Can't afford a new washer! Just need to get this thing working. Please help
1 Answer Hello Wayne. You need to check and see if the lid switch WP8318084 is bad on the unit. If it is bad on the unit, you will need to order and replace the lid switch on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Alex R. January 19, 2012 for Model Number MVWc300vw1 Washer of a friend...washer quit when it was full of water... I drained what I could...could not trun motor by hand..removed pump and there was a sock inside...put the control knob on spin and the drive motor does nothing...no hum...is the motor probably burned out?
1 Answer Hello Alex. Check and make sure it didn't throw the breaker in the house. If not, and there is power to the motor, but the motor does not run, you will need to replace the motor assembly. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...