Nick July 09, 2016 for Model Number Kenmore 110.22292100 Washer makes a knocking sound during water discharge and spin cycles. It agitates just fine. I checked the motor windings, diagram says start=8.0 ohms and high=1.7 ohms. Which I have. I'm thinking the centrifugal switch is bad?
1 Answer Nick, haven't had a centrifugal switch cause a knocking noise, not without other complaints, and it should also knock in all cycles. So, it's not likely at this point. Did you check the motor coupler for bent or broken tabs, and the pump for an obstruction or worn out bearing. You may also want to remove the agitator and tub, to check the drive block and drive tube top to see if the block or tabs on the top of the shaft are worn, "rounded off". Read More...
Tim June 06, 2016 for Model Number ATW4475VQ0 MY WASHER MAKES A LOUD BOZZING SOUND, TOOK MOTOR OUT AND ON BENCH TEST STILL BOZZING IF I GIVE IT A MANUAL TURN IT WILL ENGAGE AND GO.. SOUNDS LIKE Motor Start Capacitor ?
1 Answer Hello Tim. Based on the information you provided, it sounds like the motor WP661600 is bad and will need to be replaced. You can try just the switch, but usually the windings in the motor is bad when they do this. Read More...
Ken March 30, 2015 for Model Number Whirlpool LSC9000PW2 washer Are points for part no. 3952056 Switch, Main Drive Motor sold separately or does one have to purchase the entire switch?
1 Answer Ken, The points would not be available as a separate part and would have to purchase the switch. Read More...
Tim March 12, 2015 for Model Number RTW4440VQ1 My neighbors basement got 4 inches of water due to backed up drain. Light rust on motor. Motor hums but won't run. He never tried to run washer until all dried up. Where should I start.should I remove the motor and make sure it's dried out good and check connections and try to run motor before remounting it????
1 Answer Hello Tim. You will need to remove the motor from the unit and see if it turns by hand. If the shaft got rusted, the motor will need to be replaced. Read More...
Joe June 29, 2014 for Model Number MVWC500VW0 During the rinse cycle it will fill with water but won't agitate /spin, when I open and close the lid it will. I have replaced the timer and the lid switch. What else could it be?
1 Answer Joe, On occasion the ATC switch WPW10202616 can disrupt the circuit between the timer and the water level switch. Replacing the switch would be the next component based on the checks and parts you've replaced previously. Read More...
Bob June 24, 2014 for Model Number LSQ7030QO Washer will fill, but wont agitate or spin. It is not the coupler.
1 Answer Hello Bob. You need to check and see if the lid switch 3949247V is bad and will need to be replaced on the unit. Read More...
Art June 03, 2014 for Model Number atw4470TQ0 My washing machine does not spin or the agitator does not move when washing, but the motor is spinning.
1 Answer Hello Art. You need to check the motor coupling 285753A and see if it is broke or bad. Read More...
Ed Z April 14, 2014 for Model Number Whirlpool WTW5560SQ0 Just today I noticed a burning smell during the wash cycle. Traced it to the connection of the wire harness at the motor. The connector was burnt and partially melted. What might cause this? The washer was still working fine.
1 Answer Hello Ed. Usually that is due to a bad wiring connection on the unit. Check the connections and also look and see if the motor is overheating. Read More...
Matt February 27, 2014 for Model Number mvwc300vw0 The motor doesn't start only hums. I changed the timer but is the same problem. If I connect the motor directly, it works perfectly. Do you think is the Switch or the Main Drive Motor?
1 Answer Hello Matt, This sounds like a common problem this design gets. The unit could have lost electrical connection to the motor capacitor or it could be getting 120Vac from two sources at the same time. The second can be caused by several components which you will have to test for. If you start with the unit in spin and the connector disconnected from the motor, test from ground to each terminal for ac voltage. If there is 120Vac on more than one terminal, one of those wires will lead you back to the problem. It can be the timer or the wiring harness. Read More...
Mike February 24, 2014 for Model Number Part number of interest WHI 3952056 My washer fills, and then stops. There is no noise from the motor, agitation, or spin. I have tested the lid switch and it has continuity. I bypassed it just to be sure. I removed the motor switch and have tried testing continuity on all possible combinations with the switch engaged and not without continuity. Is this the offending part?
1 Answer Hello Mike. If there is power to the motor switch, and it does not kick in and start, you will need to replace the motor on the unit. Read More...