Jeff November 07, 2011 for Model Number lsn1000khc My washer fills with water agitates and nothing else. I have already replaced the timer and still after agitating it stops running. Help please.
1 Answer Hello Jeff. Based on the information you provided, it sounds like the lid switch 3949247V is bad and will need to be replaced. Check and see if it is broke or bad. If so, it will cause the problem you are having. Hope this helps. Read More...
Alfred July 02, 2011 for Model Number RAS7133RQ0 ROPER WASHER PROBLEMS: During my second load of clothes, my washer did nothing after the water filled in the rinse cycle. I reset the timer and still nothing. I replaced the lid switch and still nothing. Can it be the motor, capacitor or does the water level switch initiate the cycle?
1 Answer Hello Alfred. If the water level switch W10820051 does not close the contacts, the washer will not run. You will need to test and see if the switch is sending power out to the motor when the machine is full. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps.http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Roosevelt S. June 30, 2011 for Model Number LXR7244JQ3 How do determine if the Centrifugal Switch is operating properly? Is the white lever on the back supposed to move ? If so, how much?
1 Answer Hello Roosevent. You can test the switch with a meter and see if it is working properly. Also, check and make sure the motor is changing directions properly and the speeds are working correctly. If not, you will need to replace the motor assembly WP661600. The motor coupling 285753A should be tight with out play. However you can turn the coupling by hand and turn the agitator from the bottom. If the coupling is loose or broke, you will need to replace it. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps.http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Amy May 26, 2011 for Model Number LSQ9549LW0 Hi, just replaced the clutch on the washer for slow spinning. Now when it goes through the normal cycle it fills, agitates and spins fine, it just forgets to pump the water out before spinning most of the time but not always. It will go from agitate to spin skipping the pump period. Sometimes it will do it only after it fills to rinse, sometimes after the first agitate. Pulled drain hoses off and nothing clogged, pump spins freely. When it doesn't pump and goes straight to spin it makes a loud clicking noise. The coupler is still intact so not that. Sounds like it is coming from up by the pump. Thinking of replacing timer, is there anything else that could be wrong, and hopefully cheaper :) It is like it "forgets" to pump. Thanks!
1 Answer Hello Amy. You may have a bad pump WP3363394. The pump does not start to pump, until the machine goes into spin cycle. If it is not pumping out, you will need to replace the pump. Hope this helps. Read More...
Gerald B April 01, 2011 for Model Number wtw5200sq0 My washing machine worked on one load and the next load filled with water but didnt do anything else. Just started humming. Drained water manually and tried to fill again (it did) and wouldnt do anything else but hum. Any help would be appreciated.
1 Answer Hello Gerald. Check and see if there is something stuck in the pump WP3363394. If so, the pump will need to be replaced. Hope this helps. Read More...
John March 24, 2011 for Model Number RAS8244LQ1 My washing machine works fine until it gets to the spin cycle. The motor barely moves the agitator but it doesn't gain speed and soon stops. I suspect a capacitor needs replacing. Do you agree? If so, do you have a part number? Thanks for your help, John
1 Answer Hello John. It sounds like you may have a bad clutch assembly. 285785 You will need to uninstall it and see if it is worn or broke. Hope this helps. Read More...